Difference between revisions of "AY Honors/Plumbing/Answer Key"

From Pathfinder Wiki
< AY Honors‎ | PlumbingAY Honors/Plumbing/Answer Key
Line 22: Line 22:
 
===Leaky Faucet===
 
===Leaky Faucet===
 
[[Image:Faucet parts.jpg|thumb|300px]]
 
[[Image:Faucet parts.jpg|thumb|300px]]
There are many different types of faucets used in plumbing  installations.  If  you  can  repair  the compression  washer  faucet,  you  should  have  no trouble in repairing other types of faucets. A cutaway view of a compression faucet is shown in the figure above. This  faucet,  with  a  disc  washer  and  a  solid  or removable seat, requires frequent attention to maintain tight closure against water pressure.  
+
There are many different types of faucets used in plumbing  installations.  If  you  can  repair  the compression  washer  faucet,  you  should  have  no trouble in repairing other types of faucets. A cutaway view of a compression faucet is shown in the figure to the right. This  faucet,  with  a  disc  washer  and  a  solid  or removable seat, requires frequent attention to maintain tight closure against water pressure.  
  
 
When a faucet is turned off, the washer on the end of the stem rubs against the seat. Frequent use wears down the washer and eventually causes the faucet to drip. A small, steady leak in a faucet wastes water. The remedy for a dripping faucet is simply to replace the washer. Be sure to replace flat or beveled washers with washers of the same design.
 
When a faucet is turned off, the washer on the end of the stem rubs against the seat. Frequent use wears down the washer and eventually causes the faucet to drip. A small, steady leak in a faucet wastes water. The remedy for a dripping faucet is simply to replace the washer. Be sure to replace flat or beveled washers with washers of the same design.

Revision as of 01:50, 11 October 2006

Template:Honor header

1. Make a diagram showing the plumbing system of a four-room house which includes fixtures for the kitchen, bathroom, and laundry.

Plumbing diagram.jpg This diagram shows the pipes and fixtures involved in plumbing a typical four-room house.

2. Submit two pieces of iron pipe that you have threaded and connected with proper fitting.

Threading an iron pipe
Insert the correct size die into the die stock. Slide the die stock over the pipe and apply pressure with one hand. With the other hand, turn the stock handle slowly clockwise until the die has taken a bite on the pipe. Apply cutting oil to the die as the stock handle is given one complete clockwise turn and backed off a quarter turn. Repeat this action until 1/4 inch of the pipe is beyond the die stock. The pipe is now threaded properly. Turn the handle in a counterclockwise direction to remove the pipe.

3. Submit a repaired plastic (PVC), iron, or copper pipe, and tell how to repair all three.

PVC

Turn off the water, then cut out the damaged section of pipe using a hacksaw or a handsaw. Then clean the two ends of the existing pipe thoroughly and let it dry. Cut a new piece of PVC pipe the same length as the damaged and removed piece and make sure it is clean too. Apply PVC primer and cement to the ends of the replacement pipe and slide couplings over them, one on each side. Then apply PVC primer and cement to the existing pipes, and join them together. Let the cement cure for the amount of time indicated on the can. Finally, turn the water back on and check for leaks.

Iron

In galvanized pipe installations, where the fittings on either side of the leak are not readily available, the leaking section may be cut out. In this operation, one person holds the pipe with a wrench to keep it from turning in the next fitting, and another person cuts a thread on it while it is in place using a hand type of pipe threader. The cutout section is then replaced with a coupling, a pipe section of the required length, and a union.

Copper

If a copper pipe leaks, cut out the damaged section and replace it with a new section, using either soldered or compression-type joints. Soldering requires quite a bit of skill, and there is always the risk of setting a house on fire with a soldering torch. Watch where the flame goes at all times. It is easy to get absorbed in watching the solder joint and not notice that the flame is licking a joist behind the pipe. Pay attention!

4. Demonstrate ability to repair a leaky sink faucet and replace or repair toilet flush mechanisms.

Leaky Faucet

Faucet parts.jpg

There are many different types of faucets used in plumbing installations. If you can repair the compression washer faucet, you should have no trouble in repairing other types of faucets. A cutaway view of a compression faucet is shown in the figure to the right. This faucet, with a disc washer and a solid or removable seat, requires frequent attention to maintain tight closure against water pressure.

When a faucet is turned off, the washer on the end of the stem rubs against the seat. Frequent use wears down the washer and eventually causes the faucet to drip. A small, steady leak in a faucet wastes water. The remedy for a dripping faucet is simply to replace the washer. Be sure to replace flat or beveled washers with washers of the same design.

To repair a standard washer faucet, follow the steps below.

  1. First, shut off the water supply to the faucet and open the faucet all the way.
  2. Now, remove the faucet handle, bonnet, and stem.
  3. Next, remove the brass screw holding the washer to the bottom of the spindle. Replace the washer with a new one which is flat on one side and slightly rounded on the other, so it can get both horizontal and vertical pressure and provide a firm seat. Use a good quality hard-composition washer because leather or soft washers do not give long service, particularly in hot-water lines.
  4. If the brass screw is in poor condition, replace it with a new one.
  5. Examine the valve seat and repair or replace it with a new one, if necessary, before replacing the spindle; otherwise, a new washer provides adequate service for only a short time.
  6. Reface or ream solid seats with a standard reseating tool consisting of a cutter, a stem, and a handle. Rotate the tool with the cutter centered and held firmly on the worn or scored seat. Take care to prevent excessive reaming. Remove all grinding residue before reassembly. A solid seat can be replaced with a renewable seat by tapping a standard thread into the old solid seat and inserting a renewable seat.
  7. Remove renewable seats with a regular seat- removing tool or Allen wrench. When the seat is frozen to the body, apply penetrating oil to loosen it. Faucet seats can usually be tapped, reseated, or replaced without removing the faucet from its fixture.
  8. To stop leakage at the bonnet, replace the stem packing and the bib gasket.

Toilet Flush Mechanism

Before a person can repair anything, he or she must understand how that item is supposed to work. The illustration below shows the steps in a toilet flush mechanism:

1: Handle is pushed downward
2: Stopper ball is lifted, opening tank drain
3: Water level in tank begins to drop
4: Float ball lowers
5: Valve opens allowing fresh water in
6: Water is sprayed into bowl from the top
7: Water enters tank
8: Water level continues to drop
9: Water exits tank and fills bowl
10: Stopper ball reseats
11: Water level rises
12: Float ball rises
13: Valve closes


To repair a toilet flush mechanism, remove the tank lid, flush the toilet and observe. See which of the thirteen steps listed above is not happening, try to determine why it is not happening, and address the problem. In some cases it is easier to replace the flush mechanism rather than repair an existing one. The replacement parts are sold in a single package and comes with instructions geared toward a typical homeowner. Since Pathfinders tackling the Plumbing honor are not "typical," this shoud present no problems!

5. Describe the proper drainage system of the house in #1 and explain the use of traps and vents.

6. Have a knowledge of the ordinary hot and cold water system of a house and explain how to make the system safe from freezing if the house has to be left without heat during the winter.

7. Diagram at least one type of passive water heating system, such as the use of solar energy.

References