Difference between revisions of "AY Honors/Airplane Modeling/Answer Key/es"

From Pathfinder Wiki
< AY Honors‎ | Airplane ModelingAY Honors/Airplane Modeling/Answer Key/es
(Created page with "{{clear}}")
(Created page with "{{clear}}")
Line 104: Line 104:
 
{{clear}}
 
{{clear}}
  
==== Other required supplies. ====
+
{{clear}}
  
Wood glue / Hobby knifes
+
{{clear}}
  
Ruler (Metal is best)
+
{{clear}}
  
Water based sanding sealer - (I used Varathane Crystal Clear Waterborne thinned 50% with water)
+
{{clear}}
  
150 grit sandpaper
+
{{clear}}
  
Pencil / Hobby paint brushes
+
{{clear}}
  
12 Pennies
+
{{clear}}
  
Hot glue gun and glue
+
{{clear}}
  
One copy of plan page printed for each student.
+
{{clear}}
  
[[Image:Glider Stock.jpg]]
+
{{clear}}
  
 
==== Make the kits in advance ====
 
==== Make the kits in advance ====

Revision as of 21:34, 1 December 2014

Other languages:
English • ‎español • ‎français


Aeromodelismo
Asociación General

Artes y Habilidades Manuales


Destreza: 1
Año de introducción: 1944



1. Construir y volar con éxito un avión de un kit de madera de balsa y papel, que sea propulsado por una banda de goma o por gas.

2. Build a balsa wood glider from a kit and observe its flying characteristics as related to variable positions of the wings.

SIG Manufacturing is a major supplier.

Make the kits in advance

Cut the pieces from the stock to the sizes shown in the plan. Use a hobby knife and steel ruler.

Fuselage - Cut the ⅛” x ⅜” stock into 12” long sections to make 12 fuselages.

Wings - Cut 6 pieces 11” x 1½” from 2 of the 1/16” sheets to make 12 wings.

Wing Mounts - Cut ⅛” x ⅛” stock into 12 - 2½ ” sections.

Wing Mounts – Cut 24 - ¼” x 2½ ” parts for wing mounts from 1/16" sheet balsa.

Horizontal Stabilizer – Cut 12 - 3½” x 3/4” horizontal stabilizers from 1/16" sheet balsa.

Vertical Stabilizer - Cut 12 - 1½” x 1” vertical stabilizers from 1/16" sheet balsa.

(ensure grain runs the long direction on all 1/16" sheet balsa pieces)

Optionally cut the tapered notches in the fuselage for the horizontal stabilizer, or leave this step for the students depending on level of students ability with hobby knifes.

Glider kits.jpg

Each kit will contain one wing, one fuselage, one horizontal stabilizer, one vertical stabilizer, and the wing mounting pieces. One single kit is pictured below.

Glider kit.jpg

Have the students follow steps 1 through 8 to build the kits.

Instructions:

  1. Cut out all pieces.
  2. Seal and sand all pieces
  3. Assemble wing mount
  4. Glue wing to mount
  5. Mount stabilizers
  6. Use elastics to mount wing on fuselage
  7. Add penny to nose for weight, (use hot glue) and adjust wings front to back for best flight.
  8. Add cardstock ailerons, rudder, and elevators if wanted.

The following pictures are provided for reference.

Wing and wing mount:

Glider Wing Mount.jpg

Stabilizers glued to fuselage:

Glider Stabilizers.jpg

Wing mounting with elastic bands:

Glider Wing Elastics.jpg

Finished Glider:

Glider Done.jpg

Plan Page.

Glider Plan Page.jpg

3. Make and successfully fly two different styles of paper airplanes using sheets of paper between eight (20.3 cm) and fourteen (35.6 cm) inches in width and length.

Paper Plane with airfoil wings is a fun paper airplane to build. It requires more than simply folding a piece of paper up, and can be used to teach the concept of Bernoulli's Principle.

Boy Scout Paper Plane plans include many creative and fun paper airplane plans.

4. Define, locate, and explain the usage of the following basic items:

  • Fuselage
  • Wing
  • Aileron
  • Rudder
  • Horizontal stabilizer
  • Strut
  • Cockpit
  • Engine
  • Landing Gear
  • Propeller
Fuselage
The elongated body or frame of an airplane, any kind of frame or body. The central body of an airplane that is designed to accommodate the crew and passengers (or cargo).
Wing
Any surface used primarily for supporting an airplane inflight by forward motion.
Aileron
Ailerons are movable control surfaces that are present on the trailing edge of both the right and left wings of a plane. Each surface moves in opposite directions enabling a plane to roll right or left. For a plane to roll to the left, the left wing aileron moves upwards while the aileron on the right wing moves downwards.
Rudder
This is the term used to describe the part of the tail that moves back and forth. This movement causes the tail of a plane to move which then turns the plane.
Horizontal stabilizer
The horizontal "mini wing" at the tail section of the airplane. The elevator is attached to the horizontal stabilizer with hinges.
Strut
A diagonal brace going from the fuselage to the bottom of the wing consisting of a bar or rod used to support the wing on the airplane.
Cockpit
Compartment where the pilot sits while flying the aircraft.
Engine
The source of power to turn the propeller or turbines and generate thrust. Can be an internal combustion engine, jet engine, or in the case of an airplane model a rubber band engine.
Landing gear
An undercarriage that supports the weight of the plane when it is on the ground.
Propeller
The mechanical device attached to the engine that rotates to push against air and create thrust.
Dihedral
Dihedral is where the right and left wing tips are higher than the fuselage. More dihedral generally means that a plane will be more stable in the air, but will be more difficult to turn. Most planes require a bit of dihedral to fly well.
Elevator
Elevator is the term used to describe a plane's horizontal control surface on the tail. This surface enables a plane to pitch upwards or downwards. When an elevator surface moves upwards, the tail moves downwards (the nose of the plane then points up) and vice-versa. Without an elevator, it is hard to control the altitude of a plane as you can't control the rise and fall of the nose of the plane.
Thrust
The mechanical force generated by the engine to move the airplane through the air.
Vertical stabilizer
The vertical fin which is part of the tail assembly of the airplane. The rudder is attached to the vertical stabilizer with a hinge.
V-Tail
V-Tail aircraft are planes that have only 2 stabilization surfaces (in the shape of a V) instead of a conventional horizontal and vertical stabilizers. In a V-Tail aircraft, the 2 control surfaces of the V-Tail work together to give elevator and rudder responses.

Illustration of Model airplane parts.

Airplane parts.jpg