AY Honors/Cycling/Answer Key

From Pathfinder Wiki
< AY Honors‎ | CyclingAY Honors/Cycling/Answer Key /
Revision as of 21:54, 10 April 2007 by 205.175.225.24 (talk) (→‎2. Repair a punctured bicycle tire.)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Template:Honor header

1. Know the name and explain the purpose of the various parts of a bicycle.

  • Bottom bracket- Attachment of crankset to body of bike
  • Brake cable- Cable connecting the brake lever to the brake mechanism
  • Brake lever- Lever on handlebar to activate brake. Left side is front brake, right is rear brake
  • Cassette- There are up to 10 sprockets of increasing size attached to a hub housing making up a modular cassette. This housing is slipped over an outward extending splined part of the hub. The rear hub is a "freewheel" (ratcheted so the wheel is pulled around when pedaling, but allowing the wheel to spin freely while you coast). The chain is shifted from one sprocket to another by moving the right shifter lever to activate the rear derailleur.
  • Chain- Circular set of links to transfer power from chain ring to cogs of freewheel
  • Chainring- Toothed rings attached to crank that hold chain
  • Chainstay- Lower bar on portion of frame that attaches rear wheel. If there's no second tube on dual suspension bike, it is referred to as a swing arm.
  • Crank- Lever extending from bottom bracket to pedal, transfers power to chain rings
  • Derailleur- Mechanism for moving chain from one cog to another
  • Down tube- Section of frame extending downward from stem to bottom bracket
  • Dropout- Cut slot at bottom of front fork or chain stay, designed to accept axle of wheel
  • Freewheel- Set of rear cogs and idling mechanism
  • Front brake- Brake on front fork of bike
  • Front shock- Shock absorber on front fork
  • Handlebar- Horizontal bar attached to the stem with handgrips at the end, to which attach brake levers and shifters
  • Headset- Mechanism in front of frame that connects front fork to stem and handlebars
  • Head tube (steering tube) - Section of frame extending downward from top tube to down tube
  • Hub- Center portion of the wheel, to which the spokes attach
  • Idler pulley- Bottom pulley of the rear derailleur, with spring tension to keep chain tight
  • Nipple- Threaded receptacle that holds the end of the spoke into the rim
  • Pedal- Platform for the foot to press on, attached to crank
  • Rear brake- Brake on the rear wheel, usually attached to seat stay
  • Rear shock- Shock absorber for rear tire on dual-suspension bikes
  • Rim- Metal ring with U-shaped cross section, holds spokes on the inside and tire on the outside
  • Saddle (Seat) - The part your butt shouldn't be sitting on when going steep downhill
  • Seat post- Support post for saddle, fits into seat tube with mechanism for changing height
  • Seat stay- Upper support arm for the rear wheel, not present on dual-suspension bikes with simple swingarm
  • Seat tube- Section of frame extending downward from top tube to bottom bracket
  • Shifter, front- Shifting mechanism for the front derailleur, mounted on the left side of the handlebar
  • Shifter, rear- Shifting mechanism for the rear derailleur, mounted on the right side of the handlebar
  • Skewer- Metal rod that goes through the hub, attaching the wheel to the dropouts of the frame
  • Spindle- Freely rotating "axle" to which the crank arms attach, part of the bottom bracket
  • Spokes- Thick wires joining the hub to the rim, with tension adjusted via a nipple on the rim side
  • Stem- Piece that attaches the handlebar to the steering tube (headset)
  • Swingarm- Lower bar on portion of frame that attaches rear wheel with some form of spring, on full suspension bikes
  • Tyre- Where the rubber meets the road
  • Top tube- Top bar of the bicycle frame
  • Valve stem- Stem poking out of rim to inflate tyre
  • Wheel hub- Center of the wheel, to which the spokes attach

2. Repair a punctured bicycle tire.

Tools needed: tire patch kit (patch, cement, sandpaper/roughening tool) pen (ballpoint or marker) tire-iron


1) Remove wheel with flat tire from bicycle.

    It is assumed you have the skills and tools necessary to do this.  I will not describe this process here.  (A flat tire can be repaired without removing the wheel.  However that is an Advanced Procedure, and is not covered here by this author.) 

2) Identify where the hole/leak is.

    NOTE: If you can do this BEFORE removing the tire from the rim you can save yourself much effort and time later.  

Holding wheel with flat tire (& tube) closely examine exterior of tire to find what has punctured it. Include a tactile examination -- run your fingers over the tire surface. 97% of the time you will find something, a small piece of (metal) wire, a small piece of glass (often times glass is below the surface of the tire, in which case you are looking for glints of light reflecting off one surface of a shard of glass in your tire), or a biological object (splinter of wood or thorn), or a screw or a nail.

BEFORE removing object from your tire MARK THE LOCATION of the puncture. Also mark the location on the tire that corresponds to where the valve of your innertube is located. (Note: I've just told you to mark two (2) locations on your tire. This will save you time. You don't have to do it, though.)

If you do NOT find the location of the puncture mark the location of the innertube valve.

3) Remove the tire.

  If possible do not use any tools.  (This does require some muscling on your part.)  If your tire is a very tight fit over your rim use a tire-iron carefully.  (In an "extreme situation" a flat-bladed screwdriver can be used.  It is WAY-EASY to pinch-flat an innertube using a scrrewdriver.)  

Do NOT pinch your innertube between your tire-removing tool and the rim, or the tire. (If you are new to fixing flats you will probably do this once. We all do. It's part of the learning curve involved in wrenching on your bike. Learning to not pinch an innertube is best done with a wheel and tool in hand. Take your time. Good luck.)

4) Inspect the inside of your tire for punctures.

    Yes, you've inspected the outside, and now you are inspecting the inside.  This is NECESSARY if you did not find the puncture yet.  It is VERY RECOMMENDED even if you have found something already.  The idea is to leave your tire, after all this is done, with NOTHING that will put more punctures in your innertube.  

Include a tactile inspection. Mark the location of any (additional) punctures you find. REMOVE all foreign objects from your tire after marking their location.

5) Find holes in innertube.

   (This is why you marked all those puncture locations and the valve location on your tire.) 
   Align the innertube valve with the valve-location mark you made earlier on the tire.  
   Inspect the innertube in the vicinity of all the tire-puncture marks for innertube punctures.  MARK all innertube punctures.  

Maybe you were unable to find any punctures in your tire. So now you have nothing to help you find the punctures in your innertube. You may have a pinch-flat. These can be anywhere on the surface of your innertube. (Punctures from objects generally happen to the surface of the innertube that is on the outside of the "doughnut surface" that the innertube describes.)

Fill your innertube with air & listen/feel for escaping air. MARK location(s) of puncture(s). Maybe you haven't found anything yet. In this case get a container with water (bucket, washbasin, whatever) and run your innertube through the water completely submerging the innertube a section at a time. Hold each section stationary under water (fill the innertube with air just before putting innertube into water) looking for small bubbles escaping from the innertube. When pumping air in to the innertube for this test don't be afraid to pump lots of air in. (Stop pumping when innertube is twice original size. This does not mean you need to pump it up this much. I'm saying if you have no other way of determining when enough air is in the innertube, stop at twice the original size.)

Assuming you have located all the punctures in your innertube,

6) Repair innertube punctures. Roughen/clean a patch on the innertube, centered around (each) puncture, that is larger than the patch you are going to apply. (Examine patch from your patch kit to determine this size.) You will use whatever tool you patch kit provides you with -- either a (small) piece of sandpaper or a metal grater-thing.

Apply the patch cement. Apply a very thin coating to the entire area you roughened/cleaned. Allow the cement to get sticky. Test for stickyness by using a fingernail -- lightly touch one fingernail surface to a surface on the area of cement you previously applied. If it doesn't stick yet wait. If it sticks some it's about right. If you wait too long it won't stick at all, in which case you get to clean it off & re-apply.

Assuming the cement is just sticky peel off the backing from the underside of your patch and apply patch to the innertube puncture, centered on the puncture. Leave the backing that is on the top-side of your patch on. (I generally make my puncture-location marks so big that when I roughen/clean the innertube the marks are visible outside that roughened/cleaned area. This makes the centering of the patch here a lot easier.)

Press the patch onto the surface of the innertube. Use the broad part of your thumb. Use the broad part of you tire iron. You are assisting the cement to establish a complete bond between the innertube and the patch. Take a minute or two and press! You are also pressing all air out of the patch-innertube bond. (Yeah, this is the part of this process that is best taught by example/demonstration. Sorry)

As you are pressing the patch onto your innertube you may notice the top-side backing on the patch begin to come loose. This is a Good Thing. If it doesn't you get to figure out how to remove the top-side backing without removing the patch. (The top-side and bottom-side backing is there to keep the patch clean. A clean patch adheres best! Clean is Good.) "Better quality" patches have this top-side backing pre-slit making it easier to remove the top-side backing from the patch. (Most patch kits I've found recently are not "better quality".) After pressing patch onto innertube remove top-side backing.

Repeat for all punctures.

7) Set innertube aside when all puncture are patched to allow a few minutes for the cement to set and your patch to adhere.

Start cleaning up your work area. (You're almost done!)

8) Reassemble tire & innertube onto rim.

   Put just enough air into your innertube so it's barely round.  Put innertube into tire.  Fit one edge of tire over one sided of wheel rim starting with the valve area.  With your thumbs (and your tire iron IF NECESSARY) get all of one edge of tire over one rim.  

Starting at valve location push second edge of tire over wheel rim. Now you probably will have to use your tire irons. (This is why they come in sets.) If you have burley thumbs you may not need to use tire irons. (Yay!) Do everything you can to AVOID giving your (newly patched) innertube a pinch-flat. Take your time, working the tire over your wheel rim while keeping the innertube away from the rim edge. (This is why there is some air in the innertube. To avoid getting the innertube stuck between the tire and the rim edge.)

With tire completely mounted into wheel, between rims, adjust position of tire and innertube with respect to the rim so the innertube valve is sticking straight out of the valve hole. This is VERY IMPORTANT! A maladjusted innertube can put a lot of stress on one side of the innertube at the valve and rip the innertube away from the valve. Which will necessitate you replacing the innertube. (Holes at the innertube-valve junction are almost impossible to repair -- I've never been able to repair 'em anyway.)

Put 10-20 lbs of air into tire/innertube. Check valve for proper innertube-rim orientation. If the valve is sticking out of the valve hole at any angle (other than straight) let some air out and re-adjust innertube/tire and rim orietation. The rim and innertube are made to fit togather so the valve sticks straight out. Any other angle on the valve indicates things need to be re-adjusted.

When the valve has the correct angle (straight out) inspect rim-tire orientation. You are looking to make sure the tire bead is completely seated all around the rim. Look at where the tire goes into the rim. The tire should appear about "even" all the way around the edge of the rim. Tires usually have several concentric "rings" cast into the surfacce of the tire near the bead just to make this check easy. If you see the tire bead coming out of the rim in any one location do NOT put any more air into the tire. Seat the tire bead. You may have to let some air out of the tire.

When the tire bead is uniformly seated inflate the tire to full pressure. This is nearly always defined on a place on the tire. "Max pressure = ## lbs." should appear somewhere on the outside of your tire.


Hey! You're done! Clean up your work area. Put your wheel back into your bicycle. Go for a ride!

Check your tire the next day! If you had a patch that did not completely adhere you may have a slow leak. If this happens :-(( you get to find it (step 5) above) and repair it (step 6) above.) Remember to COMPLETELY remove the leaking patch before applying the new one. (Again, if you're new to this, you MAY have this happen once. It is frustrating. Somehow your patch did not completely adhere to the innertube. Dirty patch? Dirty innertube? Cement too dry? Patch not completely pressed on? These, and more, can result in a patch that does not completely adhere. I hope this does NOT happen to you.)

Happy riding! Gerhardt in Portland Apr '07

3. Take apart, clean, and properly reassemble a bicycle.

4. Adjust the brakes and front and rear derailer properly.

5. Know and practice courtesy and safety rules in bicycling.

6. What is the advantage of wearing a cycling helmet?

7. Have the following riding record:

  • a. Take three separate 10-mile (16.1 km) rides in different locations.
  • b. Take a 50-mile (80.6 km) ride in ten hours or less.

8. Know how to read a road map by routing out your 50-mile (80.6 km) course and following it accurately on an actual ride.

References