AY Honors/Springboard Diving/Answer Key

From Pathfinder Wiki
< AY Honors‎ | Springboard DivingAY Honors/Springboard Diving/Answer Key /
Revision as of 03:36, 6 December 2014 by JadeDragon (talk | contribs)
Other languages:
English


Template:Honor desc Template:Honor Master

1. Have the Advanced Beginners Swimming Honor.

For tips and instruction see [[AY Honors/Swimming - Advanced Beginner|]].

2. Demonstrate properly the following dives:*

a. Swan

Source

  1. Distance yourself. One step should do it. You need enough room to build up enough momentum, but if you run then you will probably slip.
  2. Check the depth of the pool. Only swan-dive in the deepest end reachable, as the swan-dive will take you very deep very quickly.
  3. Put your strongest leg forward. Your toes should be just hanging over the edge of the pool. Your other leg can be next to it or several inches behind, it depends on your preferences.
  4. Spread your arms to your side. This is essential for later.
  5. Push off from the side of the pool. Be sure to push slightly up, too. Snap your legs together tightly and lean forward when you do. Your body should be slightly bent.
  6. Force your arms forward so your body is in a pencil-like shape. Do this quickly, as time is tight.
  7. Angle your body at a 45+ degree angle to the water. If possible, do this as you push off from the edge.
  8. As you enter the water, lean your head forward and lift your legs up. You should enter the water smoothly with little splashing.
  9. Practice. This is essential, as nobody can perfectly execute a swan-dive first-time.
  10. Swan Dive.jpg

b. Front somersault (tuck)

Front somersault.jpg


  1. First, take a few steps forward and jump.
  2. Bounce at the end of the board.
  3. Throw your arms forward and tuck your head to your chest.
  4. During the somersault, tuck your arms and legs to your chest.
  5. You have to land the rotation on your feet or it could lead to a belly flop or a back flop.

https://www.youtube.com/watch?v=UrChg4d9bnw

c. Half twist

https://www.youtube.com/watch?v=yNTlhag-9XA

3. Demonstrate properly two of the following dives:*

Note: * Basis of Judging: Attention position for running dives; attention position on end of board for standing dives based on the following:

  • a. Approach
  • b. Spring
  • c. Way body is carried through the air (layout, tuck, or pike)
  • d. Entry into water

a. Half twist

https://www.youtube.com/watch?v=tZpUieK9UdI

b. Cutaway

c. Somersault front one and one-half

https://www.youtube.com/watch?v=bCYa9Fzrb2U

d. Back dive

https://www.youtube.com/watch?v=aLSyi4FRURw

e. Back jackknife

f. Half gainer (tuck, pike, or layout)

https://www.youtube.com/watch?v=svCWwoMmy1c

4. State the safety depths of water under a one-meter board, a three-meter board, and a tower. How far should the board project over the pool? What boards are recom­mended?

Springboards are usually located either 1.0 or 3.0 metres (3 ft 3 in or 9 ft 10 in) above the water surface. It is very seldom that one is mounted at a height other than these two standard heights.

Board Height Pool Depth Projection (NCAA) &
One meter 2.5 meters 1.5 meters
Three meter 5 meters 1.5 meters
A tower 8 meters 1.5 meters

Historically springboards were made of wood. Modern springboards (since about 1960) are made out of a single-piece extrusion of aircraft-grade aluminum. The Maxiflex Model B, the board used in all major competitive diving events, is made out of such aluminum, and is heat treated for a yield strength of 50,000 psi. The slip-resistant surface of the board is created using an epoxy resin, finished with a laminate of flint silica and alumina in between the top coats of resin. This thermal-cured resin is aqua-colored to match the water of a clean pool.

References