Difference between revisions of "AY Honors/Radio Electronics/Answer Key"

From Pathfinder Wiki
< AY Honors‎ | Radio ElectronicsAY Honors/Radio Electronics/Answer Key
Line 42: Line 42:
 
Where v is volatage (measured in volts), i is current (measured in amps), and r is resistance (measured in ohms).  The equation can also be written as
 
Where v is volatage (measured in volts), i is current (measured in amps), and r is resistance (measured in ohms).  The equation can also be written as
  
<math> i = v/r </math>
+
<math> i = frac{v}{r} </math>
  
 
and
 
and
  
<math> r = v/i</math>
+
<math> r = frac{v}{i}</math>
  
 
Basically, it means that if the voltage is held constant and the resistance is decreased, the current is increased.  Or if the resistance is held constant and the current is increased, the voltage will also increase.
 
Basically, it means that if the voltage is held constant and the resistance is decreased, the current is increased.  Or if the resistance is held constant and the current is increased, the voltage will also increase.

Revision as of 01:40, 23 October 2005

Radio Electronics

Identify at least 20 symbols used in electronics.

Identify the value of resistors by the color code

The value of a resistor is marked on the device itself by using bands of colors. The color code assigns a number to each of the following colors:

  • 0 - black
  • 1 - brown
  • 2 - red
  • 3 - orange
  • 4 - yellow
  • 5 - green
  • 6 - blue
  • 7 - violet
  • 8 - grey
  • 9 - white

Note that after black and brown, the next six colors are arranged as they are found in the rainbow. These colors can also be memorized by the use of a mnemonic such as "Black Bears Run Over Yellow Grass, But Vultures Glide over Water."

Two other colors are used to specify the tolerance of the resistor - that is, how close the actual value is to the value encoded on it:

  • 5% - gold
  • 10% - silver

If there is no gold or silver band, the resistor has a 20% tolerance.

Remember that just as "gold is better than silver," a 5% (gold) resistor is better than a 10% (silver) resistor.

On a four-band resistor, the third band represents the number of zeros that follow the first two digits, and the fourth band represents the tolerance. So a brown-black-red-gold combination would indicate a 1000 Ohm resistor with a 5% tolerance.

Resistors with tighter tolerance are usually specified with three bands indicating the numeric value and a fourth indicating the number of zeroes following.

Demonstrate proper soldering techniques

Explain the use and operation of various important components in electronics such as resistors, variable capacitors, fixed capacitors, coils, transistors, integrated circuits, diodes, and transformers.

Know and understand Ohm's Law.

If a voltage is applied across a resistor, current will flow through it. Ohm's law describes the relationship between this current, voltage, and resistance. It can be written as

[math]\displaystyle{ v = i r }[/math]

Where v is volatage (measured in volts), i is current (measured in amps), and r is resistance (measured in ohms). The equation can also be written as

[math]\displaystyle{ i = frac{v}{r} }[/math]

and

[math]\displaystyle{ r = frac{v}{i} }[/math]

Basically, it means that if the voltage is held constant and the resistance is decreased, the current is increased. Or if the resistance is held constant and the current is increased, the voltage will also increase.

Determine how to correctly place or pin integrated circuits, transistors, diodes, and capacitors in a circuit board.

What is meant by a parallel and a series circuit?

From a kit or from scratch make two of the following:

Photocell guard or counter

Siren

Simple voltmeter

Pressure sensor

Simple DC power supply

Simple transistor radio

Draw from memory, using proper symbols, the complete wiring diagram of the devices constructed in requirement 8.

List ten ways electronics are used in everyday life.