AY Honors/Wood Carving/Answer Key - Revision history

W126jep: - Category of AYHAB

2022-07-14T21:21:01Z

- Category of AYHAB

W126jep at 12:09, 15 September 2021

2021-09-15T12:09:32Z

Jomegat at 01:01, 24 July 2021

2021-07-24T01:01:00Z

W126jep: Marked this version for translation

2021-05-04T15:55:54Z

Marked this version for translation

Show changes

W126jep at 15:55, 4 May 2021

2021-05-04T15:55:42Z

Jomegat bot: Bot: Automated import of articles * existing text overwritten *

2021-03-19T04:16:41Z

Bot: Automated import of articles *** existing text overwritten ***

Jomegat bot: Bot: Automated import of articles * existing text overwritten *

2020-12-24T20:35:26Z

Bot: Automated import of articles *** existing text overwritten ***

Show changes

Jomegat bot: Jomegat bot moved page Adventist Youth Honors Answer Book/Arts and Crafts/Wood Carving to AY Honors/Wood Carving/Answer Key: Bot: Moved page

2020-12-19T05:04:42Z

Jomegat bot moved page AY Honor Wood Carving to AY Honor Wood Carving Answer Key: Bot: Moved page

W126jep: - Completed Honors category

2015-07-30T04:45:36Z

- Completed Honors category

W126jep: Marked this version for translation

2015-01-29T18:14:11Z

Marked this version for translation

@@ Line 115: / Line 115: @@
 </noinclude>
 As an honor instructor, it will be your responsibility to vet alternative designs proposed by your Pathfinders. Be on the lookout for over-ambitious designs, but be careful not to quash your Pathfinder's spirit. Offer suggestions to make the project attainable.
 <noinclude></translate></noinclude>
 {{CloseReq}} <!-- 5f -->
 {{CloseReq}} <!-- 5 -->
 {{CloseHonorPage}}

@@ Line 16: / Line 16: @@
 <!-- 2. Describe the different wood carving tools and explain how to sharpen them. -->
 ===Knife=== <!--T:21-->
-{{:Adventist Youth Honors Answer Book/Woodworking Tools/Knife}}
+{{:AY Honors/Woodworking Tools/Knife}}
 ===Chisel===
-{{:Adventist Youth Honors Answer Book/Woodworking Tools/Chisel}}
+{{:AY Honors/Woodworking Tools/Chisel}}
 ===Gouge===
-{{:Adventist Youth Honors Answer Book/Woodworking Tools/Gouge}}
+{{:AY Honors/Woodworking Tools/Gouge}}
 ===Coping saw===
-{{:Adventist Youth Honors Answer Book/Woodworking Tools/Coping saw}}
+{{:AY Honors/Woodworking Tools/Coping saw}}
 <!--T:22-->

@@ Line 1: / Line 1: @@
 {{HonorSubpage}}
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1}}
 <noinclude><translate><!--T:19-->

@@ Line 7: / Line 7: @@
 <!--T:2-->
-Softwoods are easier to carve, but hardwoods hold detail better and are stronger.  If you can manage it, hardwoods are therefore a better choice, but softwoods are very good for beginners.  Some of the best carving woods, in order of hardness are basswood,tupelo (power carving), butternut, hounduras mohagony, and walnut.
+Softwoods are easier to carve, but hardwoods hold detail better and are stronger. If you can manage it, hardwoods are therefore a better choice, but softwoods are very good for beginners. Some of the best carving woods, in order of hardness are basswood,tupelo (power carving), butternut, hounduras mohagony, and walnut.
 <noinclude></translate></noinclude>
@@ Line 27: / Line 27: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=3}}
 <noinclude><translate></noinclude>
-<!-- 3. Explain the best methods of handling the grain of wood in designing.  -->
+<!-- 3. Explain the best methods of handling the grain of wood in designing. -->
-Wood is very much like a bundle of straws glued together with a weak adhesive.  It is easy to separate the straws from one another, but more difficult to break the straws.  The woodcarver needs to keep this in mind as the piece is designed.  For instance, if carving an animal, the grain (or "straws" in our analogy) needs to run in the same direction as the legs.  Otherwise, the legs will easily break off.
+Wood is very much like a bundle of straws glued together with a weak adhesive. It is easy to separate the straws from one another, but more difficult to break the straws. The woodcarver needs to keep this in mind as the piece is designed. For instance, if carving an animal, the grain (or "straws" in our analogy) needs to run in the same direction as the legs. Otherwise, the legs will easily break off.
 <!--T:5-->
@@ Line 34: / Line 34: @@
 <!--T:6-->
-Another aspect of grain that needs careful consideration is how to work a blade along the wood with respect to it.  If the grain dives into the piece, the blade must cut in the direction in which the grain runs out of the piece rather than in the direction in which the grain runs in.  See the illustration.
+Another aspect of grain that needs careful consideration is how to work a blade along the wood with respect to it. If the grain dives into the piece, the blade must cut in the direction in which the grain runs out of the piece rather than in the direction in which the grain runs in. See the illustration.
 <noinclude></translate></noinclude>
@@ Line 40: / Line 40: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=4}}
 <noinclude><translate></noinclude>
-<!-- 4. Design and carve a plaque in low relief.  -->
+<!-- 4. Design and carve a plaque in low relief. -->
 Low relief, also known as '''Bas (pronounced bah)-relief''' is a method of sculpture which entails carving away the surface of a flat piece of wood creating a picture.
@@ Line 47: / Line 47: @@
 <!--T:9-->
-As simple tool can be constructed to help smooth out the background.  It consists of a handle made from a piece of wood about 3/4"x3/4"x10" with a wood screw set into its center, but not fully seated.  If the background is a quarter inch lower than the foreground, the screw would be set one quarter inch above the surface of the handle.  The top of the screw is then filed so that the edges of the screwhead are sharpened.  Then the carver removes the wood covering the background in the carving, but it is best to leave a border around the edges.  Then the tool is used to smooth out the background with the handle riding along the raised border.  Once the background is smoothed, the carver can turn his or her attention to the foreground, shaping and smoothing it as desired.
+As simple tool can be constructed to help smooth out the background. It consists of a handle made from a piece of wood about 3/4"x3/4"x10" with a wood screw set into its center, but not fully seated. If the background is a quarter inch lower than the foreground, the screw would be set one quarter inch above the surface of the handle. The top of the screw is then filed so that the edges of the screwhead are sharpened. Then the carver removes the wood covering the background in the carving, but it is best to leave a border around the edges. Then the tool is used to smooth out the background with the handle riding along the raised border. Once the background is smoothed, the carver can turn his or her attention to the foreground, shaping and smoothing it as desired.
 <noinclude></translate></noinclude>
@@ Line 53: / Line 53: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5}}
 <noinclude><translate></noinclude>
-<!-- 5. Design and carve two of the following items:  -->
+<!-- 5. Design and carve two of the following items: -->
 <noinclude></translate></noinclude>
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5a}}
@@ Line 60: / Line 60: @@
 <!--T:11-->
-To make a whistle, you will need a block of softwood, a dowel, and a drill bit that is the same diameter as the dowel.  Drill a hole into the end of the block of wood.  The hole can go all the way through, or it can stop before it exits the other side.  Then cut a notch (C in the diagram) in the top of this piece such that it exposes the hole that was just bored.  This notch should be about {{units|4 cm|1.5 inches}} from the end.  It needs to be vertical nearest the mouth end and slanted on the other side.
+To make a whistle, you will need a block of softwood, a dowel, and a drill bit that is the same diameter as the dowel. Drill a hole into the end of the block of wood. The hole can go all the way through, or it can stop before it exits the other side. Then cut a notch (C in the diagram) in the top of this piece such that it exposes the hole that was just bored. This notch should be about {{units|4 cm|1.5 inches}} from the end. It needs to be vertical nearest the mouth end and slanted on the other side.
 <!--T:12-->
-Shave one edge of the dowel (A) flat to make the airway (B), and cut off a section of the dowel such that its length is the same as the distance from the notch to the mouth end.  Insert the dowel into the bored hole with the airway towards the notch to test the fit.  At this point blowing into the whistle should produce a tone (try it).  If it does not produce a tone, review the diagram and try to figure out what went wrong.  One possibility is that the pitch is too high for the human ear.  You can adjust the tone by making the hole go deeper into the wood (unless it already goes all the way through).  When the tone is satisfactory, remove the dowel, apply some glue, and reinsert.  When the glue dries shape the mouthpiece as desired and carve your design on the outside.
+Shave one edge of the dowel (A) flat to make the airway (B), and cut off a section of the dowel such that its length is the same as the distance from the notch to the mouth end. Insert the dowel into the bored hole with the airway towards the notch to test the fit. At this point blowing into the whistle should produce a tone (try it). If it does not produce a tone, review the diagram and try to figure out what went wrong. One possibility is that the pitch is too high for the human ear. You can adjust the tone by making the hole go deeper into the wood (unless it already goes all the way through). When the tone is satisfactory, remove the dowel, apply some glue, and reinsert. When the glue dries shape the mouthpiece as desired and carve your design on the outside.
 <noinclude></translate></noinclude>
@@ Line 69: / Line 69: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5b}} <!--T:13-->
 <noinclude><translate></noinclude>
-A letter opener is really nothing more than a wooden knife.  Make it as fancy as you like.
+A letter opener is really nothing more than a wooden knife. Make it as fancy as you like.
 <noinclude></translate></noinclude>
@@ Line 75: / Line 75: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5c}} <!--T:14-->
 <noinclude><translate></noinclude>
-A tray can be made by joining four narrow pieces of wood at the ends using box joints or dovetail joints.  A slot should be milled near the bottom edge of these boards so that it can receive a tray bottom.  The tray bottom can be cut from eighth inch luan or some other thin plywood or mason board.  The bottom piece should not be glued - allow it to float in the joint so that the tray does not crack when it contracts and expands as the temperature and humidity vary.  Assemble three of the sides, then slip the bottom into the slots and add the fourth side.  Glue the corner joints.  Once the tray is assembled, you can carve the sides as you please.
+A tray can be made by joining four narrow pieces of wood at the ends using box joints or dovetail joints. A slot should be milled near the bottom edge of these boards so that it can receive a tray bottom. The tray bottom can be cut from eighth-inch luan or some other thin plywood or mason board. The bottom piece should not be glued - allow it to float in the joint so that the tray does not crack when it contracts and expands as the temperature and humidity vary. Assemble three of the sides, then slip the bottom into the slots and add the fourth side. Glue the corner joints. Once the tray is assembled, you can carve the sides as you please.
 <noinclude></translate></noinclude>
@@ Line 81: / Line 81: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5d}} <!--T:15-->
 <noinclude><translate></noinclude>
-Bookends can be carved from two short sections of 4"x4" lumber, but make sure it is not pressure treated.  Cut off two sections 4 to 6 inches long, making sure the cut is square.  The end grain of this cut will be the bottom of the bookend.  Most commercial 4x4 lumber will be softwood, so if you want hardwood, you will have to look a little harder.  If you cannot find a hardwood 4x4, you can make one from smaller pieces of stock by laminating them (that is, gluing several pieces together).  Make it interesting by laminating both dark and light-colored species of wood.  You can also use chunks of firewood.  If you use firewood, you will need to plane one surface and saw another flat.  The sawn surface will serve as the bottom, and the planed surface will support the books.
+Bookends can be carved from two short sections of 4"x4" lumber, but make sure it is not pressure treated. Cut off two sections 4 to 6 inches long, making sure the cut is square. The end grain of this cut will be the bottom of the bookend. Most commercial 4x4 lumber will be softwood, so if you want hardwood, you will have to look a little harder. If you cannot find a hardwood 4x4, you can make one from smaller pieces of stock by laminating them (that is, gluing several pieces together). Make it interesting by laminating both dark and light-colored species of wood. You can also use chunks of firewood. If you use firewood, you will need to plane one surface and saw another flat. The sawn surface will serve as the bottom, and the planed surface will support the books.
 <!--T:16-->
-Once you have two flat surfaces that form a 90° angle, sketch your design on the wood and rough it out with a saw, chisels, gouges or all of the above.  As the carving takes shape, use finer tools until the piece is ready to take a finish such as paint or varnish.  If your tools are sharp, you should not need to sand the piece before finishing.  Sanding poses the danger of removing detail from the carving and should be considered carefully before attempting.
+Once you have two flat surfaces that form a 90° angle, sketch your design on the wood and rough it out with a saw, chisels, gouges or all of the above. As the carving takes shape, use finer tools until the piece is ready to take a finish such as paint or varnish. If your tools are sharp, you should not need to sand the piece before finishing. Sanding poses the danger of removing detail from the carving and should be considered carefully before attempting.
 <noinclude></translate></noinclude>
@@ Line 90: / Line 90: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5e}} <!--T:17-->
 <noinclude><translate></noinclude>
-A clock case need not be any more than a board with a clock movement attached.  Carve your design into the face of the board in low-relief.  Clock movements can be bought at most hobby and craft stores.  Buy the clock movement, drill any necessary holes, and make sure the movement fits before you start carving though.  It would be a shame to destroy a work of art by accidentally drilling a hole in the wrong place, or finding that you must remove part of the artwork to fit the clock in place.  Once the movement has been mounted on the blank case and you see that it fits, remove it and set it aside.  You don't need the hassle of carving around the clock hands.
+A clock case need not be any more than a board with a clock movement attached. Carve your design into the face of the board in low-relief. Clock movements can be bought at most hobby and craft stores. Buy the clock movement, drill any necessary holes, and make sure the movement fits before you start carving though. It would be a shame to destroy a work of art by accidentally drilling a hole in the wrong place, or finding that you must remove part of the artwork to fit the clock in place. Once the movement has been mounted on the blank case and you see that it fits, remove it and set it aside. You don't need the hassle of carving around the clock hands.
 <noinclude></translate></noinclude>
@@ Line 96: / Line 96: @@
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5f}} <!--T:18-->
 <noinclude><translate></noinclude>
-As an honor instructor, it will be your responsibility to vet alternative designs proposed by your Pathfinders.  Be on the lookout for over-ambitious designs, but be careful not to quash your Pathfinder's spirit.  Offer suggestions to make the project attainable.
+As an honor instructor, it will be your responsibility to vet alternative designs proposed by your Pathfinders. Be on the lookout for over-ambitious designs, but be careful not to quash your Pathfinder's spirit. Offer suggestions to make the project attainable.
 [[Category:Adventist Youth Honors Answer Book|{{SUBPAGENAME}}]]
 <noinclude></translate></noinclude>

@@ Line 1: / Line 1: @@
-<languages /><br />
+{{HonorSubpage}}
 <section begin="Body" />
 {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1}}
@@ Line 113: / Line 101: @@
 {{CloseReq}} <!-- 5f -->
 {{CloseReq}} <!-- 5 -->
-<section end="Body" />
+{{CloseHonorPage}}

@@ Line 10: / Line 10: @@
 |insignia=Wood_Carving_Honor.png
 }}
-==1. Explain the qualities of hard and soft woods and the best woods for wood carving.==
+==1. Explain the qualities of hard and soft woods and the best woods for wood carving.== <!--T:1-->
 The hard woods are oak, beech, birch, maple, walnut, ash, hickory, all of which belong to the broad leaf variety of trees. The soft woods are pine, spruce, hemlock, cedar, cypress, which belong to the "coniferous" or cone-bearing family. The hard woods are on an average two or three times as hard as the others, but some of the so-called hard woods are really quite soft, and vice versa.
 Softwoods are easier to carve, but hardwoods hold detail better and are stronger.  If you can manage it, hardwoods are therefore a better choice, but softwoods are very good for beginners.  Some of the best carving woods, in order of hardness are basswood,tupelo (power carving), butternut, hounduras mohagony, and walnut.
-==2. Describe the different wood carving tools and explain how to sharpen them.==
+==2. Describe the different wood carving tools and explain how to sharpen them.== <!--T:3-->
 ===Knife===
 {{:Adventist Youth Honors Answer Book/Woodworking Tools/Knife}}
@@ Line 25: / Line 26: @@
 {{:Adventist Youth Honors Answer Book/Woodworking Tools/Coping saw}}
-==3. Explain the best methods of handling the grain of wood in designing. ==
+==3. Explain the best methods of handling the grain of wood in designing. == <!--T:4-->
 Wood is very much like a bundle of straws glued together with a weak adhesive.  It is easy to separate the straws from one another, but more difficult to break the straws.  The woodcarver needs to keep this in mind as the piece is designed.  For instance, if carving an animal, the grain (or "straws" in our analogy) needs to run in the same direction as the legs.  Otherwise, the legs will easily break off.
 [[Image:Planing_wood_with_the_grain.PNG|300px]] [[Image:Planing_wood_against_the_grain.PNG|300px]]
 Another aspect of grain that needs careful consideration is how to work a blade along the wood with respect to it.  If the grain dives into the piece, the blade must cut in the direction in which the grain runs out of the piece rather than in the direction in which the grain runs in.  See the illustration.
-==4. Design and carve a plaque in low relief. ==
+==4. Design and carve a plaque in low relief. == <!--T:7-->
 Low relief, also known as '''Bas (pronounced bah)-relief''' is a method of sculpture which entails carving away the surface of a flat piece of wood creating a picture.
 The portrayed image is raised above the background flat surface so that for a piece of wood one inch thick the non-image (background) area may be a half inch thick when the art work has been completed, and the image area will vary from one half to one inch.
 As simple tool can be constructed to help smooth out the background.  It consists of a handle made from a piece of wood about 3/4"x3/4"x10" with a wood screw set into its center, but not fully seated.  If the background is a quarter inch lower than the foreground, the screw would be set one quarter inch above the surface of the handle.  The top of the screw is then filed so that the edges of the screwhead are sharpened.  Then the carver removes the wood covering the background in the carving, but it is best to leave a border around the edges.  Then the tool is used to smooth out the background with the handle riding along the raised border.  Once the background is smoothed, the carver can turn his or her attention to the foreground, shaping and smoothing it as desired.
-==5. Design and carve two of the following items: ==
+==5. Design and carve two of the following items: == <!--T:10-->
 ===a. Whistle ===
 [[Image:Recorder300px.png]]
 To make a whistle, you will need a block of softwood, a dowel, and a drill bit that is the same diameter as the dowel.  Drill a hole into the end of the block of wood.  The hole can go all the way through, or it can stop before it exits the other side.  Then cut a notch (C in the diagram) in the top of this piece such that it exposes the hole that was just bored.  This notch should be about {{units|4 cm|1.5 inches}} from the end.  It needs to be vertical nearest the mouth end and slanted on the other side.
 Shave one edge of the dowel (A) flat to make the airway (B), and cut off a section of the dowel such that its length is the same as the distance from the notch to the mouth end.  Insert the dowel into the bored hole with the airway towards the notch to test the fit.  At this point blowing into the whistle should produce a tone (try it).  If it does not produce a tone, review the diagram and try to figure out what went wrong.  One possibility is that the pitch is too high for the human ear.  You can adjust the tone by making the hole go deeper into the wood (unless it already goes all the way through).  When the tone is satisfactory, remove the dowel, apply some glue, and reinsert.  When the glue dries shape the mouthpiece as desired and carve your design on the outside.
-===b. Letter opener ===
+===b. Letter opener === <!--T:13-->
 A letter opener is really nothing more than a wooden knife.  Make it as fancy as you like.
-===c. Tray ===
+===c. Tray === <!--T:14-->
 A tray can be made by joining four narrow pieces of wood at the ends using box joints or dovetail joints.  A slot should be milled near the bottom edge of these boards so that it can receive a tray bottom.  The tray bottom can be cut from eighth inch luan or some other thin plywood or mason board.  The bottom piece should not be glued - allow it to float in the joint so that the tray does not crack when it contracts and expands as the temperature and humidity vary.  Assemble three of the sides, then slip the bottom into the slots and add the fourth side.  Glue the corner joints.  Once the tray is assembled, you can carve the sides as you please.
-===d. Bookends ===
+===d. Bookends === <!--T:15-->
 Bookends can be carved from two short sections of 4"x4" lumber, but make sure it is not pressure treated.  Cut off two sections 4 to 6 inches long, making sure the cut is square.  The end grain of this cut will be the bottom of the bookend.  Most commercial 4x4 lumber will be softwood, so if you want hardwood, you will have to look a little harder.  If you cannot find a hardwood 4x4, you can make one from smaller pieces of stock by laminating them (that is, gluing several pieces together).  Make it interesting by laminating both dark and light-colored species of wood.  You can also use chunks of firewood.  If you use firewood, you will need to plane one surface and saw another flat.  The sawn surface will serve as the bottom, and the planed surface will support the books.
 Once you have two flat surfaces that form a 90° angle, sketch your design on the wood and rough it out with a saw, chisels, gouges or all of the above.  As the carving takes shape, use finer tools until the piece is ready to take a finish such as paint or varnish.  If your tools are sharp, you should not need to sand the piece before finishing.  Sanding poses the danger of removing detail from the carving and should be considered carefully before attempting.
-===e. Clock case ===
+===e. Clock case === <!--T:17-->
 A clock case need not be any more than a board with a clock movement attached.  Carve your design into the face of the board in low-relief.  Clock movements can be bought at most hobby and craft stores.  Buy the clock movement, drill any necessary holes, and make sure the movement fits before you start carving though.  It would be a shame to destroy a work of art by accidentally drilling a hole in the wrong place, or finding that you must remove part of the artwork to fit the clock in place.  Once the movement has been mounted on the blank case and you see that it fits, remove it and set it aside.  You don't need the hassle of carving around the clock hands.
-===f. Equivalent items of your choice===
+===f. Equivalent items of your choice=== <!--T:18-->
 As an honor instructor, it will be your responsibility to vet alternative designs proposed by your Pathfinders.  Be on the lookout for over-ambitious designs, but be careful not to quash your Pathfinder's spirit.  Offer suggestions to make the project attainable.
 <noinclude></translate></noinclude>
 [[Category:Adventist Youth Honors Answer Book|{{SUBPAGENAME}}]]
 [[Category:Adventist Youth Honors Answer Book/Completed Honors|{{SUBPAGENAME}}]]

AY Honors/Wood Carving/Answer Key - Revision history

W126jep: - Category of AYHAB

W126jep at 12:09, 15 September 2021

Jomegat at 01:01, 24 July 2021

W126jep: Marked this version for translation

W126jep at 15:55, 4 May 2021

Jomegat bot: Bot: Automated import of articles *** existing text overwritten ***

Jomegat bot: Bot: Automated import of articles *** existing text overwritten ***

Jomegat bot: Jomegat bot moved page Adventist Youth Honors Answer Book/Arts and Crafts/Wood Carving to AY Honors/Wood Carving/Answer Key: Bot: Moved page

W126jep: - Completed Honors category

W126jep: Marked this version for translation

Jomegat bot: Bot: Automated import of articles * existing text overwritten *

Jomegat bot: Bot: Automated import of articles * existing text overwritten *