Difference between revisions of "AY Honors/Model Rocketry - Advanced/Answer Key"
(Marked this version for translation) |
m |
||
(10 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | < | + | {{HonorSubpage}} |
− | <noinclude><translate><!--T: | + | |
+ | <section begin="Body" /> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1}} | ||
+ | <noinclude><translate><!--T:7--> | ||
</noinclude> | </noinclude> | ||
− | {{ | + | <!-- 1. Have the Model Rocketry honor. --> |
− | + | {{honor_prerequisite|honor=Model Rocketry}} | |
− | | | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | }} | ||
− | <!--T: | + | <!--T:8--> |
− | < | + | <noinclude></translate></noinclude> |
− | + | {{CloseReq}} <!-- 1 --> | |
− | + | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=2}} | |
− | {{ | + | <noinclude><translate><!--T:9--> |
− | + | </noinclude> | |
− | + | <!-- 2. From a kit, build, successfully launch, and recover a boost glider. --> | |
− | A boost glider is a model having a rocket-powered ascent, transitions to a glider at the apex of its flight, and then glides (usually in circles) back to the ground using aerodynamic surfaces (wings). | + | A boost glider is a model having a rocket-powered ascent, transitions to a glider at the apex of its flight, and then glides (usually in circles) back to the ground using aerodynamic surfaces (wings). Most boost gliders locate the rocket engines towards the front of the aircraft, as this eases many of the design challenges involved in powered flight. The rocket portions are ejected from the craft during transition (gliders that do not separate are called ''rocket gliders'' rather than ''boost gliders''). The Space Shuttle is an example of a boost glider (though it is most decidedly not a model!) Estes makes a model Space Shuttle which is a boost glider. See [http://www.esteseducator.com/Pdf_files/2266.pdf here] for more information about boost gliders. |
<!--T:5--> | <!--T:5--> | ||
Though these models are among the most challenging rocket models to build, a modeler with careful attention to detail has every reason to expect success. | Though these models are among the most challenging rocket models to build, a modeler with careful attention to detail has every reason to expect success. | ||
− | + | <!--T:10--> | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
<noinclude></translate></noinclude> | <noinclude></translate></noinclude> | ||
− | [[Category: | + | {{CloseReq}} <!-- 2 --> |
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=3}} | ||
+ | <noinclude><translate><!--T:11--> | ||
+ | </noinclude> | ||
+ | <!-- 3. Design, build (not from a kit), finish, and paint a single-stage rocket. Check for stability, and successfully launch and recover this rocket. --> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{CloseReq}} <!-- 3 --> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=4}} | ||
+ | <noinclude><translate><!--T:12--> | ||
+ | </noinclude> | ||
+ | <!-- 4. Do one of the following: --> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=4a}} | ||
+ | <noinclude><translate><!--T:13--> | ||
+ | </noinclude> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{CloseReq}} <!-- 4a --> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=4b}} | ||
+ | <noinclude><translate><!--T:14--> | ||
+ | </noinclude> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{CloseReq}} <!-- 4b --> | ||
+ | {{CloseReq}} <!-- 4 --> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5}} | ||
+ | <noinclude><translate><!--T:15--> | ||
+ | </noinclude> | ||
+ | <!-- 5. Design an electrical launch system. When this has been approved by your instructor, build this system and use it to launch rockets at least five times. --> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{CloseReq}} <!-- 5 --> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=6}} | ||
+ | <noinclude><translate><!--T:16--> | ||
+ | </noinclude> | ||
+ | <!-- 6. Describe and demonstrate single station altitude tracking. With the aid of a helper, track the same rocket three times using three different sizes of engines and compare altitudes with an altitude finder. --> | ||
+ | <noinclude></translate></noinclude> | ||
+ | {{CloseReq}} <!-- 6 --> | ||
+ | {{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=7}} | ||
+ | <noinclude><translate><!--T:17--> | ||
+ | </noinclude> | ||
+ | <!-- 7. Compare the velocity and altitude of two different weights of rockets using the same size engine. --> | ||
+ | <noinclude></translate></noinclude> | ||
+ | |||
+ | {{CloseReq}} <!-- 7 --> | ||
+ | |||
+ | [[Category:Instructor Required{{GetLangSuffix}}|{{SUBPAGENAME}}]] | ||
+ | {{CloseHonorPage}} |
Latest revision as of 21:25, 1 January 2023
Skill Level
2
Year
1970
Version
28.11.2024
Approval authority
General Conference
1
For tips and instruction see Model Rocketry.
2
A boost glider is a model having a rocket-powered ascent, transitions to a glider at the apex of its flight, and then glides (usually in circles) back to the ground using aerodynamic surfaces (wings). Most boost gliders locate the rocket engines towards the front of the aircraft, as this eases many of the design challenges involved in powered flight. The rocket portions are ejected from the craft during transition (gliders that do not separate are called rocket gliders rather than boost gliders). The Space Shuttle is an example of a boost glider (though it is most decidedly not a model!) Estes makes a model Space Shuttle which is a boost glider. See here for more information about boost gliders.
Though these models are among the most challenging rocket models to build, a modeler with careful attention to detail has every reason to expect success.
3
4
4a
4b
5
6
7