Difference between revisions of "AY Honors/String Art"

From Pathfinder Wiki
< AY HonorsAY Honors/String Art
m (Fix Tab Name transclusion)
m (Fix Honor categories)
Line 6: Line 6:
 
|skill=1
 
|skill=1
 
|year=1975
 
|year=1975
|category=Arts and Crafts
+
|category=Arts, Crafts and Hobbies
 
|authority=General Conference
 
|authority=General Conference
 
|insignia=String_Art_Honor.png  
 
|insignia=String_Art_Honor.png  

Revision as of 16:51, 16 January 2021

Other languages:
English • ‎español

Template:Honor tab

Overview

The Challenging Part

The most challenging requirement of this honor is probably this:

5. Complete one original string art hanging on wood for display.

[[AY Honors/String Art/Requirements|Tab Name/Printable Version]]


1. Describe the following: string craft, symmography, geometric stitchery.

2. Draw and stitch on cardboard in equally spaced points:

a. A right angle

b. An acute angle

c. An obtuse angle

3. Name three ways to prepare wood for string art.

4. Use stringing methods on wood to do four of the following:

a. Filled circle

b. Hollowed circle

c. Star

d. Edging

e. Curve from within

f. Curve from without

g. Filler

h. Wing weave


5. Complete one original string art hanging on wood for display.


Printable Answer Key Tab Name/Edit Answer Key


1

Describe the following: string craft, symmography, geometric stitchery.


String Craft
String Craft is making something (craft or art) out of string.
Symmography
Symmography is creating 3D designs with string without knotting or knitting.
Geometric Stitchery
Geometric Stitchery is like Symmography but instead of using nails to hold the string on the surface of the media you use a needle or precut holes to go through the media and come out to a new point in the media. Much like sewing on a patch.


2

Draw and stitch on cardboard in equally spaced points:



3

Name three ways to prepare wood for string art.


There are many ways to prepare the wood for string art:

Paint
Paint covers the wood and gives you a smooth surface with the color(s) of your choice.
Stain
Stain changes the color of the wood while still showing the nature and texture of the wood. Stained wood can be lacquered or varnished to make it glossy.
Lacquer
Lacquer (clear) protects the wood without changing its color. It leaves a glossy finish.
Felt
Cover the wood with felt. Use staples on the back or a thin, even coat of white glue on the front. Dots of glue will show through, so if you are going to use glue, it must be spread evenly, as if you were painting with it. Stretch the felt over the wood tightly, eliminating all wrinkles.

Once the wood has been finished, the string artist will drive small nails partway into the board. These nails are the points around which the strings are run. When setting the nails, at least half the nail should be left exposed above the wood. Care must be taken to drive the nails to a sufficient depth so that they do not pull out when placed under tension by the string. The project will look far better if all the nails are set to the same height, and if they are perfectly vertical.

If you have difficulty setting the nails (big fingers plus little nails equal trouble!) try holding the nail in place with a pair of needle nose pliers.

It is a good idea to draw the pattern out on paper first. Then tape the paper over the wood and drive the nails through it. Once the nails are in place, the paper should be removed. It is tempting to leave the paper in place to serve as a guide while running the string, but this temptation should be resisted. It is nearly impossible to remove the paper without removing at least some of the string. Do yourself a favor and remove the paper before running the string.

To begin, anchor the first string to the first nail using a slip knot. Tug on it to be sure it will hold before spending a lot of time running the string. If it pulls loose halfway through the design, it will be difficult to salvage all that hard work.


4

Use stringing methods on wood to do four of the following:


4a

Filled circle


In a 'Filled circle', the string would cross the center point of the circle. There would be no empty space in the center area of the circle.


4b

Hollowed circle


In a 'Hollowed circle', the string would not go pass the center point of the circle. There would be no string in the center area of the circle.


4c

Star


The hollow and filled circles are also of a star design.


4d

Edging


Curve from within, Curve from without
Edging basically edges or outlines the design.


4e

Curve from within


When you curve from within the string covers some part of the inside curve.


4f

Curve from without


The Curve from within and Curve from without are two different types of edging. In the example here, we are using a circle. Edging basically edges the design. When you curve from within the string covers some part of the inside curve. When you curve from without the string does not cross the space on the inside of the curve (because the nails in the wood keeps them on the outside of the curve).



4g

Filler



4h

Wing weave




5

Complete one original string art hanging on wood for display.


This is your part. Enjoy!
StringArt-Project1.png
StringArt-Project2.png



References


Content on this wiki is generated by people like you, and no one has created a lesson plan for this honor yet. You could do that and make the world a better place.

See AY Honors/Model Lesson Plan if you need ideas for creating one.