Especialidades JA/Azulejos de mosaico/Respuestas
Azulejos de mosaico | ||
---|---|---|
División Norteamericana
|
Destreza: 1 Año de introducción: 2020 |
Requisitos
La especialidad de Azulejos de mosaico es un componente de la Maestría Artesanía. |
1
1a
1b
2
3
4
The main difference between unsanded and sanded grout is the presence or absence of sand. Unsanded cement-based grout is a smooth mixture of Portland cement, powdered pigments and water. Epoxy grouts are made of resin and hardener. Sanded cement-based grout and sanded epoxy grouts are basically the same as the previously mentioned mixtures but with sand added. The sand thickens the grout to prevent shrinking in the joints.
Both cement-based grouts and epoxy grouts come in sanded and unsanded types and can both be used with floor and wall tiles. Cement-based grouts are traditionally used in residential applications. Epoxy grouts are more ideal for situations where the tiles will be exposed to harsh materials, such as acids and greases.
Unsanded grout should be used in joints that are less than 1/8-inch-wide. It has a smooth texture and clings well to vertical surfaces, which makes it useful for grouting ceramic wall tiles. Sanded grout should be used for flooring and wall tile joints wider than 1/8 inch because it resists shrinkage and cracking. It is possible to use sanded grout in thinner joints, but forcing the bulky mixture into these joints is difficult, and pinholes may occur in your finished grout lines. Joints larger than 3/8 inch need heavily-sanded grout mixture, which is typically labeled as a wide-joint mixture and is available at most hardware and flooring stores.
The size of the tile joint usually dictates which type of grout to use, but sometimes the type of tile is the deciding factor. For example, unsanded grout is recommended for highly polished, easily scratched tiles such as marble because the aggregate in sanded grouts may damage these types of tiles. Unsanded grout should not be used in floor tiles, however, because the grout can crack and break under the pressure of floor traffic.
5
- Tile Cutter
- Diamond Drill Bit
- Tile Mortar Mixer
- Buckets
- Tile Trowel
- Rubber Grout Float
- Tile Spacers
- Sponge
- Knee Pads
- Level
- Tape Measure
6
6a
6b
7
Good grout makes for a great tile job and here is the best way to apply grout. After the grout is totally mixed, apply a generous amount to the tile surface and use a foam tile float to distribute it completely filling the tile joints all the way to the bottom by pressing firmly. Once the joints are filled, hold the float at a steep angle and begin removing excess grout from the face of the tile. Always move in a diagonal direction. If you don’t, you run the risk of scooping out grout from the joints you just filled. Dip a cellulose grout sponge in water and wring out most but not all of the water. Then wash the face of the tiles, being careful not to pull the grout out of the joints. Cutting the sponge in half on a tile saw creates a nice square edge that’s ideal for getting into corners. For a final rinsing, dip the sponge in clean water and wring it out thoroughly. Then tip the sponge up so that only the leading edge is touching the tile. Move diagonally across the surface with straight overlapping strokes. Every couple of strokes, flip the sponge around and use one of the remaining clean edges.
8
9
Referencias
- Categoría: Tiene imagen de insignia
- Adventist Youth Honors Answer Book/Honors/es
- Adventist Youth Honors Answer Book/es
- Adventist Youth Honors Answer Book/Skill Level 1/es
- Adventist Youth Honors Answer Book/Honors Introduced in 2020/es
- Adventist Youth Honors Answer Book/North American Division/es
- Adventist Youth Honors Answer Book/Arts and Crafts/es
- Adventist Youth Honors Answer Book/Arts and Crafts/Primary/es
- Adventist Youth Honors Answer Book/Artisan Master Award/es
- Adventist Youth Honors Answer Book/Stage 0/es