Difference between revisions of "AY Honors/Lapidary/Answer Key"

From Pathfinder Wiki
< AY Honors‎ | LapidaryAY Honors/Lapidary/Answer Key
Line 1: Line 1:
 
{{honor_header|2|1967|Arts and Crafts|North American Division}}
 
{{honor_header|2|1967|Arts and Crafts|North American Division}}
 
==1. Name four safety precautions to be taken when sawing rocks. ==
 
==1. Name four safety precautions to be taken when sawing rocks. ==
 +
# Wear eye protection
 +
# Do not wear loose clothing or accessories (watches, jewelry, etc) that can get caught in a machine.
 +
# Use only a properly grounded electrical outlet for lapidary equipment.
 +
# Never use cutting tools dry.  They must be continually wetted when in use.
 +
# Read all instructions and safety precautions before operating equipment.
 +
# Set equipment up on a sturdy, level surface.
 +
 
==2. Name two types of diamond saw lubricating and cooling solutions and their purpose. ==
 
==2. Name two types of diamond saw lubricating and cooling solutions and their purpose. ==
 
==3. Explain how a diamond saw cuts rocks, how it gets dull, and how it can be sharpened. ==
 
==3. Explain how a diamond saw cuts rocks, how it gets dull, and how it can be sharpened. ==

Revision as of 04:20, 17 January 2008

Template:Honor header

1. Name four safety precautions to be taken when sawing rocks.

  1. Wear eye protection
  2. Do not wear loose clothing or accessories (watches, jewelry, etc) that can get caught in a machine.
  3. Use only a properly grounded electrical outlet for lapidary equipment.
  4. Never use cutting tools dry. They must be continually wetted when in use.
  5. Read all instructions and safety precautions before operating equipment.
  6. Set equipment up on a sturdy, level surface.

2. Name two types of diamond saw lubricating and cooling solutions and their purpose.

3. Explain how a diamond saw cuts rocks, how it gets dull, and how it can be sharpened.

4. Describe the five basic steps to follow in bringing a slab or a flat surface to a polish.

5. What important precaution should be taken between each stage of grinding and sanding?

6. What is a template, and how is it used?

7. What is a cabochon, and what is the usual thickness of the slab from which it is made?

A cabochon is a gemstone which has been shaped and polished as opposed to faceted. The resulting form is usually a convex top with a flat bottom. Cutting "en cabochon" is usually applied to opaque gems, while faceting is usually applied to transparent stones. Hardness is also taken into account as softer gemstones with a hardness lower than 7 on the Moh's hardness scale are easily scratched, mainly by silicon dioxide in dust and grit. This would quickly make translucent gems unattractive. Instead they are polished as cabochons, making the scratches less evident.

The one notable exception to this is the case of asteriated stones such as star sapphires and chatoyant stones such as cat's eye chrysoberyl, where a domed cabochon cut is used to show the star or eye, which would not be seen in a faceted cut.

Cabochons are usually cut from slabs ranging from one to three eighths of an inch thick (3 to 10 mm).

8. How do you decide the best angle or position to slab a specimen?

9. Explain two methods of wet sanding while shaping and polishing the rock.

10. From what material are polishing compounds made? If a scratch appears while polishing, how is it removed?

11. Saw, trim, properly dop, and carry a cabochon through the necessary grinding, sanding, and polishing stages to a high gloss or glassy finish.

12. Mount the cabochon on some type of backing, such as a stick pin, sweater pin, key ring, etc., with cement.

References