|*Edits to the Pathfinder Wiki will be disabled on July 27, 2021 in preparation for an upgrade. The upgrade is scheduled to take place on August 3, 2021. During the upgrade, we expect the Wiki to be available only intermittently. Once the upgrade is complete, users will again be able to perform edits. Thanks!|
*Las ediciones al Wiki de Conquistadores se desactivarán el 27 de julio de 2021 en preparación para una actualización. La actualización está programada para el 03 de agosto de 2021. Durante la actualización, esperamos que el Wiki esté disponible solo de forma intermitente. Una vez que se complete la actualización, los usuarios podrán volver a realizar ediciones. ¡Gracias!
Investiture Achievement/Guide/Outdoor Living
Under the guidance of an adult staff member, teach the Knot Tying Honor.
Knot tying is an important part of Pathfindering with tie ins to Investiture Achievement and many other honors such as the various Camping Honors, Rock Climbing, Pioneering and others.
- Friends are required to tie and know the practical use of 10 knots
- Companions are required to tie and know the practical use of 20 knots
- Explorers must earn the Knot Tying Honor
- Guides must, under the guidance of an adult staff member, teach the Knot Tying Honor
- Master Guides are required to earn or hold the Knot Tying Honor.
An effective way to teach knots in a club setting is to have the staff and the older Pathfinders (the ones who already have the Knot Tying Honor) each teach a single knot at a knot tying station. The Pathfinders who are learning the knots will rotate through the stations. After a set time, ring a bell to signal that it's time to rotate, and do not allow the students to rotate until the bell rings (otherwise, they will all gravitate to the same table).
Using this approach, each of the teachers need only learn a single knot well enough to teach it, and the students will have a chance to receive one-on-one instruction for every knot. Allow at least seven or eight minutes per station. You can do this over more than one meeting if necessary, and you can involve the entire club at once rather than only a single unit.
Prior to the meeting, the rope may be cut to the proper length. Some instructors consider cutting rope during a meeting a waste of valuable teaching time, while others use it as an opportunity to teach proper binding of the rope. To prevent the cut rope from unravelling, wrap a small piece of duct tape around it before you make the cut - then cut the tape in half. This will save time, as it binds both ends of the cut in one shot.
The length of each rope should be suited to the knot it will be used for. Note that a figure eight knot does not require as much rope as a timber hitch, and that it is impossible to tie a knot on a rope that it too short to hold it. Conversely, using too much rope for small knots is a waste of good rope (and money!). Remember that the amount of rope wasted on each knot will be multiplied by the number of students.
A good way to determine proper rope length is to tie the desired knot using a long piece of rope, cut it, and then untie it. That's how long it needs to be. Cut as many of that length as you will have students, put them in a plastic baggie, and label the bag. You may have the knot instructors cut their own ropes, or you may have a squad of TLT's do this. Or you could do it yourself (but that would be depriving your TLT's and/or instructors of a valuable experience).
Two knot tying stations can easily share an eight foot table and a hot-melt glue gun - assuming the students will be mounting the knots on a board as they tie them. If you are organized and have the space, you can store their knot boards from year to year and let them add to it each year. By the time they are in the Ranger class, they will appreciate not having to tie 25 knots all at once.
A good knot board can be made from a length of lumber - 24"x12"x3/4" makes a good sized board if you are using quarter-inch diameter rope. A stick can be fastened along the edge of the board to make a convenient place to tie the hitches.
For a professional-looking knot board, prepare labels for the knots using a label maker. Again, this is something that should be done prior to the meeting, as making labels and distributing them is not an effective use of instruction time. You should also make labels with each student's name (or have students label their boards neatly) so that they will be able to find their knot boards in the future and to prevent disputes over knot board ownership. You might also consider labeling the knot boards before they are given to the students (and before the knots are tied), as this makes it easy to figure out which knots the student still needs to learn.
Complete Guide requirements
You must complete the requirements listed above this one on the current page.
Complete one of the following honors not previously earned:
| Note: The editors of this answer book feel that there is an error in the official version of this requirement.
There is a discrepancy in this requirement. The first honor is stated as Pioneering, yet in the activity diaries the picture shown is that of Orienteering. The other languages, Spanish and French, put Orienteering instead of Pioneering. Is the image placed for Orienteering the correct option or is Pioneering the correct option? The previously revised requirements, the AY classes, show the Pioneering honor.
Look over the requirements for each honor before deciding which one to earn. It is best to get a consensus from the rest of your Guide class before deciding on an honor, as these are easier to earn in a group than by oneself. Below are links to the answer keys to these honors: