|*Edits to the Pathfinder Wiki will be disabled on July 27, 2021 in preparation for an upgrade. The upgrade is scheduled to take place on August 10, 2021. During the upgrade, we expect the Wiki to be available only intermittently. Once the upgrade is complete, users will again be able to perform edits. Thanks!|
*Las ediciones al Wiki de Conquistadores se desactivarán el 27 de julio de 2021 en preparación para una actualización. La actualización está programada para el 10 de agosto de 2021. Durante la actualización, esperamos que el Wiki esté disponible solo de forma intermitente. Una vez que se complete la actualización, los usuarios podrán volver a realizar ediciones. ¡Gracias!
Adventist Youth Honors Answer Book/Arts and Crafts/Silk Screen Printing - Advanced
|Silk Screen Printing - Advanced|
| General Conference
|| Skill Level 3
Year of Introduction: 1974
- 1 1. Have the Silk Screen Printing Honor.
- 2 2. Properly stretch and secure silk screen fabric to a frame.
- 3 3. Know what fabrics can be used in silk screening and the advantages of each. What factors influence the choice of mesh count for the screen?
- 4 4. Understand and use each of the following silk screen printing techniques:
- 5 5. Use two of the following techniques in meeting requirement 4:
- 6 6. Print on a material other than paper or fabric, such as glass, metal, or leather.
- 7 References
This Honor is a component of the Artisan Master Award.
1. Have the Silk Screen Printing Honor.
This Wiki has a page with instructions and tips for earning the Silk Screen Printing honor.
2. Properly stretch and secure silk screen fabric to a frame.
The frame is made of wood, and should allow a three inch border around the artwork to be printed. In other words, if the artwork is four inches across, the frame must be 4+3+3=10 inches wide, allowing for a three inch boarder on both sides. This is true of both the vertical and horizontal dimensions of the frame. You can buy a frame from a silkscreen supplier, or build one yourself, but it is critically important that it be flat on the bottom. You can also use a wooden picture frame or a frame made for stretching an artist's canvas.
Once the frame has been selected, you should stretch the screen over it and staple it about once per inch. Make sure there are no wrinkles. Once the screen has been securely attached, trim around the edges with scissors.
3. Know what fabrics can be used in silk screening and the advantages of each. What factors influence the choice of mesh count for the screen?
Silk was the first type of fabric used in silk screening, and lent its name to the art. It is still used sometimes, but polyesters are cheaper and are commonly used today. There are two types of polyesters used in silk screening, monofilament and multifilament. Monofilaments are made from single strands of polyester, whereas multifilaments are made from multiple strands twisted together. Monofilaments are preferred, as they are less elastic and can therefore be stretched much tighter than multifilaments. They are also more sturdy and can be used repeatedly in printing several runs. Further, monofilaments can be used to create more finely registered prints. However, multifilaments produce a slightly different texture in the printed product, and sometimes this is preferred. Indeed, the use of multifilaments are common in the industry.
The mesh count is the number of threads per inch in the silk screen. The higher the mesh count, the finer the detail in the finished product. However, one must also consider the type of ink used and make sure that it is well-matched to the mesh count. Some inks will not penetrate through a very fine mesh.
4. Understand and use each of the following silk screen printing techniques:
a. Hand cut film stencil method
In this method, a sheet of film which has been coated with lacquer is cut into a stencil with a sharp knife. The film is generally available at art supply store. Once it has been cut out, lacquer thinner is used to adhere the film to the outside of the silkscreen (the part that comes into contact with the item being printed). If the stencil is adhered to the other side of the screen, the squeegee can remove the lacquer during the printing process.
After the film has been adhered to the screen, it is allowed to set until it is dry. The film is then peeled off the screen, leaving the lacquer behind.