Difference between revisions of "AY Honors/Hot Air Balloons/Answer Key"

From Pathfinder Wiki
< AY Honors‎ | Hot Air BalloonsAY Honors/Hot Air Balloons/Answer Key
 
m
 
(236 intermediate revisions by 33 users not shown)
Line 1: Line 1:
−
[[Image:Jacques Étienne Montgolfier.jpg|thumb|right|200px|Jacques Étienne Montgolfier]]
+
{{HonorSubpage}}
 +
<section begin="Body" />
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1}}
 +
<noinclude><translate><!--T:47-->
 +
</noinclude>
 +
<!-- 1. State the role each of the following played in the development of flying balloons. -->
 +
<noinclude></translate></noinclude>
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1a}}
 +
<noinclude><translate><!--T:48-->
 +
</noinclude>
 +
<gallery>
 +
Image:Josephmontgolfier.jpg|Joseph Michel Montgolfier
 +
Image:Jacques Étienne Montgolfier.jpg|Jacques-Etienne Montgolfier
 +
</gallery>
  
−
{{For|the indie pop band|The Montgolfier Brothers}}
+
<!--T:3-->
−
The brothers, '''Joseph Michel Montgolfier''' ([[26 August]] [[1740]] – [[26 June]] [[1810]]) and '''Jacques-Étienne Montgolfier'''  ([[6 January]] [[1745]] – [[2 August]] [[1799]]) were the inventors of the '''''montgolfière''''', ''globe airostatique'' or [[hot air balloon]]. The brothers succeeded in launching the first manned ascent to carry a young physician and an audacious army officer into the sky. They were later ennobled with their father and brothers and sisters as '''de Montgolfier'''.
+
Joseph-Michel Montgolfier (26 August 1740 – 26 June 1810) and Jacques-Étienne Montgolfier (6 January 1745 – 2 August 1799) were the inventors of the montgolfière, or airship. The brothers succeeded in launching the first manned ascent, carrying a young physician and an audacious army officer into the sky.
  
−
==Early years==
+
<!--T:4-->
−
The brothers were born into a family of [[paper]] manufacturers in [[Annonay]], in [[Ardèche]], France to Pierre Montgolfier ([[Tence]], [[21 February]] [[1700]] &ndash; [[Vidalon]], [[1 June]] [[1793]]), ennobled as Pierre de Montgolfier in December [[1783]] by King [[Louis XVI of France]] and wife (married at [[Annonay]], [[14 July]] [[1727]]) Anne Duret ([[Annonay]], [[14 February]] [[1701]] &ndash; [[Vidalon]], [[11 March]] [[1760]]), the parents of sixteen children. He was the son of Hoe Montgolfier ([[Beaujeau]], [[10 March]] [[1673]] &ndash; [[Davezieux]], [[6 February]] [[1743]]), [[papermaker]], and wife (married at [[Tence]], [[14 January]] [[1693]]) Marguerite Chelles ([[Job]], bef. [[1676]] &ndash; [[Davezieux]], [[17 May]] [[1736]]). She was the daughter of Charles Duret (d. [[Annonay]], [[21 May]] [[1738]]) and wife (married on [[30 September]] [[1691]]) Isabeau Bruyere.<ref>[http://www.wargs.com/noble/anna.html Ancestry of Princess Anna Cecilia of Bourbon-Sicily (b. 1971)<!-- Bot generated title -->]</ref> Pierre established his eldest son Raymond Montgolfier, later Raymond de Montgolfier ([[Vidalon]], [[28 July]] [[1730]] &ndash; [[Lyon]], [[31 July]] [[1792]] and married on [[5 March]] [[1761]] to Claudine Devant who died at [[Annonay]], [[1800]], by whom he had issue) as his successor. As an initially sent away to school to learn other professions.
+
Of the two brothers, it was Joseph who first contemplated building "machines". Joseph observed laundry drying over a fire incidentally form pockets that billowed upwards. Joseph set about building a box-like chamber {{units|1 by 1 by 1.3 meters|3 by 3 by 4 ft}} out of very thin wood and covering the sides and top with lightweight taffeta cloth. Under the bottom of the box he crumpled and lit some paper. The contraption quickly lifted off its stand and collided with the ceiling. Joseph then recruited his brother to balloon building.
  
−
[[Image:Josephmontgolfier.jpg|thumb|200px|left|Joseph Michel Montgolfier]]
+
<!--T:5-->
 +
The two brothers then set about building a contraption 3 times larger in scale (27 times larger in volume). The lifting force was so great that they lost control of their craft on its very first test flight on 14 December 1782. The device floated nearly 2 kilometres (about 1.2 mi). It was destroyed after landing by the "indiscretion" of passersby.
  
−
Joseph (12th child) possessed a typical inventor's temperament -- a maverick and dreamer but impractical in terms of business and personal affairs. Étienne had a much more even and businesslike temperament than Joseph.  As the 15th child he was sent to Paris to train as an architect.  However, after the sudden and unexpected death of Poopsie in 1772, he was recalled to Annonay to run the family business.  In the subsequent 10 years, Étienne applied his talent for technical innovation to the family business; papermaking was a high-tech industry in the 18th century. He succeeded in incorporating the latest Dutch innovations of the day into the family mills. His work led to recognition by the government of France as well as the awarding of a government grant to establish the Montgolfier factory as a model for other French papermakers, but also to the family wealth.poo
+
<!--T:49-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 1a -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1b}} <!--T:6-->
 +
<noinclude><translate><!--T:50-->
 +
</noinclude>
 +
[[image:Early flight 02562u (4).jpg|thumb|200px|The first untethered balloon flight, by Rozier and the Marquis d'Arlandes on 21 November 1783.]]
 +
Jean-François Pilâtre de Rozier (30 March 1754 – 15 June 1785) was a French chemistry and physics teacher, and one of the first pioneers of aviation. His balloon crashed near Wimereux in the Pas-de-Calais during an attempt to fly across the English Channel, and he and his companion, Pierre Romain, became the first known victims of an air crash.
  
−
==Initial experiments==
+
<!--T:7-->
 +
In June 1783, he witnessed the first balloon flight of the Montgolfier brothers. On 19 September, he assisted with the untethered flight of a sheep, a cockerel and a duck from the front courtyard of the Palace of Versailles. After a variety of tests in October, he made the first manned free flight in history on 21 November 1783, accompanied by the ambitious Marquis d'Arlandes. During the 25-minute flight using a Montgolfier hot air balloon, they traveled 12 kilometres from the Château de la Muette to the Butte-aux-Cailles, then in the outskirts of Paris, attaining an altitude of 3,000 feet.
 +
{{clear}}
  
−
Of the two brothers, it was Joseph who first contemplated building "''machines''". Gillispie puts it as early as 1777 when Joseph observed laundry drying over a fire incidentally form pockets that billowed upwards.<ref>C.C. Gillispie, The Montgolfier brothers and the invention of aviation 1783-1784, p. 15.</ref> Joseph made his first definitive experiments in November of 1782 while living in [[Avignon]].  He reported, some years later, that he was watching a fire one evening while contemplating one of the great military issues of the day -- an assault on the fortress of [[Gibraltar]], which had proved impregnable by both sea and land.<ref>C.C. Gillispie, p. 16.</ref>   Joseph mused on the possibility of an air assault using troops lifted by the same force that was lifting the embers from the fire. He believed that contained within the smoke was a special gas, called 'Montgolfier Gas', with a special property he called 'levity'.  
+
<!--T:51-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 1b -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1c}} <!--T:8-->
 +
<noinclude><translate><!--T:52-->
 +
</noinclude>
 +
In December of 1783, these two flew the first gas balloon, filled with hydrogen. This flight lasted for at least 2 hours, starting from the Tuileries gardens in Paris, and landing outside Paris where it was destroyed by terrified peasants.  
  
−
As a result of these musings, Joseph set about building a box-like chamber 1x1x1,3m (3 [[foot|ft]] by 3 ft by 4 ft) out of very thin wood and covering the sides and top with lightweight [[taffeta]] cloth.  Under the bottom of the box he crumpled and lit some paper.  The contraption quickly lifted off its stand and collided with the ceiling.  Joseph then recruited his brother to balloon building by writing the prophetic words: "Get in a supply of [[taffeta]] and of cordage, quickly, and you will see one of the most astonishing sights in the world."<ref>C.C. Gillispie, p. 17.</ref> 
+
<!--T:9-->
 +
Charles went on to discover [[w:Charles's_Law| Charles' Law]] which describes the relationship between the density of a gas and its temperature.
  
−
The two brothers then set about building a contraption 3 times larger in scale (27 times larger in volume). The lifting force was so great that they lost control of their craft on its very first test flight on [[14 December]] [[1782]]. The device floated nearly 2 kilometres (about 1.2 mi). It was destroyed after landing by the "indiscretion" of passersby.<ref>C.C. Gillispie, p. 21.</ref>
+
<!--T:53-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 1c -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1d}} <!--T:10-->
 +
<noinclude><translate><!--T:54-->
 +
</noinclude>
 +
From 11 August to 17 August, 1978, these three completed the first transatlantic balloon flight in the [[w:Double_Eagle_II|Double Eagle II]]. They began their flight from Presque Isle, Maine and ended their flight at Miserey, France.  
  
−
==Public demonstrations==
+
<!--T:11-->
−
[[Image:Early flight 02562u (2).jpg|thumb|left|150px|First public demonstration in [[Annonay]], [[1783-06-04]].]]
+
Ben Abruzzo and Larry Newman were also pilots on the [[w:Double_Eagle_V|Double Eagle V]] which in 1981 was the first balloon to cross the Pacific Ocean.
−
The brothers decided to make a public demonstration of a balloon in order to establish their claim to its invention.  They constructed a globe-shaped balloon of [[sackcloth]] with three thin layers of paper inside.  The envelope could contain nearly 790 m³ (28,000 cubic feet) of air and weighed 225 kg (500 lb).  It was constructed of four pieces (the dome and three lateral bands), and held together by 1,800 buttons.  A reinforcing "fish net" of cord covered the outside of the envelope.
 
  
−
On [[4 June]] [[1783]], they flew this craft as their first public demonstration at Annonay in front of a group of dignitaries from the ''Etats particulars''. Its flight covered 2 km (1.2 mi), lasted 10 minutes, and had an estimated altitude of 1.600 - 2.000m (5,200 - 6,600 ft).  Word of their success quickly reached Paris.  Etienne went to the capital to make further demonstrations and to solidify the brothers' claim to the invention of flight.  Joseph, given his unkempt appearance and shyness, remained with the family. Etienne was ''the epithome of sober virtues ... modest in clothes and manner...''<ref>S. Schama (1989) Citizens. A Chronicle of the French Revolution, p. 125.</ref>  He was dressed stylishly in black.
+
<!--T:55-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 1d -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=1e}} <!--T:12-->
 +
<noinclude><translate><!--T:56-->
 +
</noinclude>
 +
On March 1, 1999, Bertrand Piccard and Brian Jones began the first balloon flight to circumnavigate the earth. Their flight was a success and ended on March 20, 1999. The flight took 19 days and 21 hours. The flight started in Switzerland and ended in Egypt.
  
−
[[Image:Montgolfier Balloon.JPG|thumb|right|150px|A model of the Montgolfier brothers balloon at the [[London Science Museum]]]]
+
<!--T:57-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 1e -->
 +
{{CloseReq}} <!-- 1 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=2}}
 +
<noinclude><translate><!--T:58-->
 +
</noinclude>
 +
<!-- 2. Cite the principle of Archimedes, and briefly describe how it applies to each of the following: -->
 +
::Archimedes' Principle states: ''any body fully or partially submerged in a fluid is buoyed up by a force equal to the weight of the fluid displaced.''
 +
<noinclude></translate></noinclude>
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=2a}}
 +
<noinclude><translate><!--T:59-->
 +
</noinclude>
 +
Cork is less dense than water, and weighs less than the volume of water displaced, causing the cork to float.
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 2a -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=2b}}
 +
<noinclude><translate><!--T:60-->
 +
</noinclude>
 +
Ships, though made of dense materials, are shaped so that much of the interior is air. Because the weight of the ship and its cargo is less than the volume of water displaced, the ship will float.
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 2b -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=2c}}
 +
<noinclude><translate><!--T:61-->
 +
</noinclude>
 +
As long as a balloon plus the gas it contains weighs less than the atmospheric air which it displaces, the balloon will float in the air.
  
−
In collaboration with the successful manufacturer, [[Jean-Baptiste Réveillon]], Etienne constructed a 37,500 cubic foot envelope of taffeta coated with a varnish of [[alum]]. The balloon was sky blue and with golden flourishes, signs of the [[zodiac]], suns. The design was the influence of Réveillon, a [[wallpaper]] maker. The next test was on the 11th of September from the parc ''la [[Folie Titon]]'', close to the house of Réveillon. There was some concern about the effects of flight into the upper atmosphere on living creatures. The king proposed to launch two criminals, but it is most likely that the inventors decided to send animals aloft first.  
+
<!--T:62-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 2c -->
 +
{{CloseReq}} <!-- 2 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=3}}
 +
<noinclude><translate><!--T:63-->
 +
</noinclude>
 +
<!-- 3. Using a textbook of Chemistry, or a reference book of scientific tables, draw up a simple table showing the composition of air by weight and by volume. -->
 +
{|border=1 cellspacing=1 cellpadding=5 align="center"
 +
|-
 +
! Gas || Air Percentage || Weight of pure gas
 +
|-
 +
|Nitrogen || 78%|| 1.25 g/liter
 +
|-
 +
|Oxygen ||21%|| 1.43 g/liter
 +
|-
 +
|Argon ||.93%|| 1.78 g/liter
 +
|-
 +
|Carbon Dioxide ||.03%||1.96 g/liter
 +
|-
 +
|Other (including Neon, Helium, <br>Hydrogen, Xenon, & Radon)|| .04%||
 +
|}
  
−
On [[19 September]] [[1783]] the ''Aerostat Réveillon'' was flown with the first living beings in a basket attached to the balloon: a sheep, called Montauciel (Climb-to-the-sky), a duck and a rooster. This demonstration was performed before a huge crowd at the royal palace in [[Versailles]], before King [[Louis XVI of France]], Queen [[Marie Antoinette]].<ref>C.C. Gillispie, p. 92-3.</ref>  The flight lasted approximately eight minutes, covered two miles, and obtained an altitude of about 1500 feet. The craft landed safely after flying.
+
<!--T:15-->
 +
The average weight of air in a balloon can be worked out using rough percentages 80% Nitrogen and 20% oxygen as the make up of air. Atomic weight of Nitrogen is 14. Atomic weight of Oxygen is 16. Nitrogen and Oxygen gases are formed using two atoms. So for a balloon containing one mole (22.4 liters) of air, we can compute its weight:
  
−
==Human flight==
+
<!--T:16-->
−
With the successful demonstration at Versailles, and again in collaboration with Réveillon, Etienne started construction of a 60,000 cubic foot balloon for the purpose of making flights with humans. The craft was 75 feet tall and 46 feet in diameter. The balloon was tested in tethered flights on [[15 October]] by [[Pilâtre de Rozier]], a twenty-six-year-old physician, who offered his services. On the [[17 October]] the experiment was repeated before a group of scientists and [[19 October]] Rozier and André Giroud de Villette, a wallpaper manufacturer from Madrid, reached 324 feet within 15 seconds along retaining ropes.
+
80% x 28 + 30% x 32 = 0.8 x 28 + 0.2 x 32 = 22.4 + 6.4 = 28.8
  
−
On [[21 November]] the first free flight by humans was made by Pilâtre, together with an army officer, the [[marquis d'Arlandes]]. The flight began near the [[Bois de Boulogne]] in the parc of the [[Château de la Muette]] in the western outskirts of Paris. They flew aloft about 3,000 feet above [[Paris]] for a distance of nine kilometres. After 25 minutes the machine landed between the windmills, outside the city ramparts, on the [[Butte-aux-Cailles]]. Enough fuel remained on board at the end of the flight to have allowed the balloon to fly four to five times as far. However, burning embers from the fire were scorching the balloon fabric and had to be daubed out with sponges. As it appeared it could destroy the balloon, Pilâtre took off his coat to stop the fire.
+
<!--T:17-->
 +
So a balloon with 22.4 liters of air weighs 28.8 grams plus the weight of the balloon.  
  
−
The ascensions made a sensation. Numerous engravings commemorated the events. Chairs were designed with balloon backs, and mantel clocks were produced in enamel and gilt-bronze replicas set with a dial in the balloon. One could buy crockery decorated with naive pictures of balloons.
+
<!--T:18-->
 +
<!-- See talk page for discussion of this section
  
−
==Following launches==
+
<!--T:19-->
−
In 1766, the British scientist [[Henry Cavendish]] had discovered hydrogen, by adding sulphuric acid to iron, tin, or zinc shavings.  The development of [[gas balloon]]s proceeded almost in parallel with the work of the Montgolfiers.  This work was led by [[Jacques Alexandre César Charles|M. Charles]]. On the 27th of August a [[hydrogen]] balloon was launched from the [[Champ de Mars]] in Paris.  Six thousand people paid for a seat.  A downpour of rain ended the show.  On December, the 1st, prof. Charles went up into the sky twice.
+
To calculate weights of gases. One mole of the gas has a volume of 22.4 liters.
  
−
Work on each type of balloon was spurred on by the knowledge that there was a competing group and alternative technology. For a variety of reasons, including the fact that the French government chose to put a proponent of hydrogen in charge of balloon development, [[hot air balloon]]s were superseded by [[hydrogen]] balloons.  Hydrogen balloons became the predominant technology for the next 180 years.
+
<!--T:20-->
 +
Helium has an atomic weight of 4 g per mole so the weight of 22.4 l = 4 grams. Oxygen as a gas has two Oxygen atoms so the weight is twice the atomic weight.
 +
-->
  
−
Hydrogen balloons were used for all major ballooning accomplishments such as the crossing of the English Channel on [[7 January]] [[1785]], by the tireless aviators [[Jean-Pierre Blanchard]] and Dr. [[John Jeffries]], from Boston.
+
<!--T:64-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 3 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=4}}
 +
<noinclude><translate><!--T:65-->
 +
</noinclude>
 +
<!-- 4. Draw up a simple table showing a comparison of the atomic number, atomic weight, and density of hydrogen, helium, nitrogen, and oxygen. -->
  
−
==Competing claims==
 
−
Some claim that the hot air balloon was actually invented some 74 years earlier by the [[Portugal|Portuguese]] priest [[Bartolomeu de Gusmão]].<ref> [http://www.instituto-camoes.pt/cvc/ciencia/p2.html Reis, Fernando. ''Bartolomeu de Gusmão''.Ciência em Portugal. Centro Virtual Camões] in Portuguese</ref> A description of his invention was published in 1709, in Vienna, and another one that was lost was found in the Vatican (circa 1917).<ref> [http://purl.pt/706/3/ Gusmao, Bartolomeu de. ''Reproduction fac-similé d'un dessin à la plume de sa description et de la pétition addressée au Jean V. (de Portugal) en langue latine et en écriture contemporaine (1709) retrouvés récemment dans les archives du Vatican du célèbre aéronef de Bartholomeu Lourenco de Gusmão "l'homme volant" portugais, né au Brésil (1685-1724) précurseur des navigateurs aériens et premier inventeur des aérostats.'' 1917 (Lausanne : Impr. Réunies S. A..)] in French and Latin</ref>
 
−
However, this claim is not generally recognized by aviation historians outside the Portuguese speaking community, in particular the [[Fédération Aéronautique Internationale|FAI]].
 
  
−
==External links==
+
<!--T:22-->
 +
{|border=1 cellpadding=5 align="center"
 +
|-
 +
!
 +
![[w:Atomic_number|Atomic Number]]
 +
![[w:Atomic_weight|Atomic Weight]]
 +
![[w:Density|Density]] (g/cm³)
 +
|-
 +
![[w:Hydrogen|Hydrogen]]
 +
!1
 +
!1.008
 +
!align="left"|0.00008988
 +
|-
 +
![[w:Helium|Helium]]
 +
!2
 +
!4.003
 +
!align="left"|0.0001785
 +
|-
 +
![[w:Nitrogen|Nitrogen]]
 +
!7
 +
!14.01
 +
!align="left"|0.0012506
 +
|-
 +
![[w:Oxygen|Oxygen]]
 +
!8
 +
!16.00
 +
!align="left"|0.001429
 +
|}
  
−
*[http://www.chm.bris.ac.uk/webprojects2003/hetherington/final/montgolfier_bros.html "Lighter than air: the Montgolfier brothers"]
+
<!--T:66-->
−
*[http://www.start-flying.com/Montgolfier.htm "Balloons and the Montgolfier brothers"]
+
<noinclude></translate></noinclude>
−
* http://www.twinring.jp/english/balloon/what_balloon/
+
{{CloseReq}} <!-- 4 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=5}}
 +
<noinclude><translate><!--T:67-->
 +
</noinclude>
 +
<!-- 5. Name two gases that are used in flying gas filled balloons. -->
 +
Hydrogen & Helium are both less dense than air and may be used when flying a balloon. Warm air is also used for flying balloons, since it is less dense than cold air.
  
−
{{DEFAULTSORT:Montgolfier Brothers}}
+
<!--T:24-->
 +
*Note: Hydrogen burns violently when ignited. After the destruction of the Hindenburg, hydrogen was largely abandoned for the flying of manned balloons.
  
−
[[Category:French balloonists]]
+
<!--T:68-->
−
[[Category:French people]]
+
<noinclude></translate></noinclude>
−
[[Category:Sibling duos]]
+
{{CloseReq}} <!-- 5 -->
−
[[Category:People of the Industrial Revolution]]
+
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=6}}
−
[[Category:Aviation pioneers]]
+
<noinclude><translate><!--T:69-->
−
[[Category:Papermakers]]
+
</noinclude>
−
[[Category:1740 births]]
+
<!-- 6. Explain how heat/temperature affect the density of air, and how this applies to flying hot air balloons. -->
−
[[Category:1745 births]]
+
As described by [[w:Charles's_Law|Charles' Law]], heat applied to a gas will cause its molecules to move farther apart, reducing it's density. When the air in a balloon is heated above the temperature of the surrounding air, the air in the balloon becomes less dense than the air outside the balloon. Because the balloon is less dense, it will float or rise. The greater the difference in temperature between the air in the balloon and the surrounding air, the greater the difference in density between the air inside and outside the balloon, which increases the lift that the balloon will generate. This explains why balloons are mostly launched in cooler weather.
−
[[Category:1799 deaths]]
 
−
[[Category:1810 deaths]]
 
  
−
[[cs:Joseph-Michel Montgolfier]]
+
<!--T:70-->
−
[[de:Montgolfier]]
+
<noinclude></translate></noinclude>
−
[[es:Hermanos Montgolfier]]
+
{{CloseReq}} <!-- 6 -->
−
[[fr:Frères Montgolfier]]
+
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=7}}
−
[[hr:Braća Montgolfier]]
+
<noinclude><translate><!--T:71-->
−
[[io:Montgolfier fratuli]]
+
</noinclude>
−
[[it:Fratelli Montgolfier]]
+
<!-- 7. Explain the role of each of the following in the structure and flying of a hot air balloon. -->
−
[[he:האחים מונגולפייה]]
+
; a. Envelope: The outer skin of the balloon, forming the container that holds the gas.
−
[[nl:Gebroeders Montgolfier]]
+
; b. Support structure: The framework of larger balloons.
−
[[ja:モンゴルフィエ兄弟]]
+
; c. Throat: The lower opening through which the hot flame is applied to heat the air.
−
[[no:Brødrene Montgolfier]]
+
; d. Fuel source: The fuel used to heat the air to make the balloon less dense than the surrounding air.
−
[[pl:Bracia Montgolfier]]
+
 
−
[[pt:Etiene e Joseph Montgolfier]]
+
<!--T:72-->
−
[[ro:Fraţii Montgolfier]]
+
<noinclude></translate></noinclude>
−
[[ru:Монгольфье]]
+
{{CloseReq}} <!-- 7 -->
−
[[sr:Браћа Монголфје]]
+
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=8}}
−
[[fi:Montgolfierin veljekset]]
+
<noinclude><translate><!--T:73-->
−
[[sv:Montgolfier]]
+
</noinclude>
−
[[th:มองโกลไฟเออร์]]
+
<!-- 8. Name two materials that may be used for the envelope of a hot air balloon, and compare the advantages each accords because of its properties. -->
−
[[tr:Montgolfier Kardeşler]]
+
;Paper: Paper may be used for model hot air balloons because of ease of acquisition and low price.
−
[[uk:Монгольф'є Джосеф Мішель та Жак-Етьєнн]]
+
;Plastic: Plastic may be used for model hot air balloons because it is water resistant, easy to work with, and easy to acquire.
−
[[zh:孟格菲兄弟]]
+
;Fabric: Fabric is usually used for larger, manned balloons. The fabric is specially treated.
 +
 
 +
<!--T:74-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 8 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=9}}
 +
<noinclude><translate><!--T:75-->
 +
</noinclude>
 +
<!-- 9. Describe how flying balloons have served a useful function in -->
 +
<noinclude></translate></noinclude>
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=9a}}
 +
<noinclude><translate><!--T:76-->
 +
</noinclude>
 +
Military uses include: “eyes in the sky”, observation of enemy troops and positions, delivery of explosives to enemy positions, and defensive use of entangling incoming enemy flying craft.
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 9a -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=9b}}
 +
<noinclude><translate><!--T:77-->
 +
</noinclude>
 +
Scientific uses include instrument transport for data collecting, atmospheric studies, and aerial photography.
 +
 
 +
<!--T:78-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 9b -->
 +
{{CloseReq}} <!-- 9 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=10}}
 +
<noinclude><translate><!--T:79-->
 +
</noinclude>
 +
<!-- 10. At what time of the day do most sport balloon flights take place? Why? -->
 +
Early morning is best because the air has cooled over night making the difference of temperature inside & outside greater, thus increasing buoyancy.
 +
 
 +
<!--T:80-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 10 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=11}}
 +
<noinclude><translate><!--T:81-->
 +
</noinclude>
 +
<!-- 11. Describe how a pilot controls the vertical movement of -->
 +
<noinclude></translate></noinclude>
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=11a}}
 +
<noinclude><translate><!--T:82-->
 +
</noinclude>
 +
The pilot controls the vertical movement of a hot air balloon by burning more fuel to make the air in the balloon hotter, causes the air in the balloon to become less dense, making it rise. Conversely, turning off the flame and allowing the air in the balloon to cool renders the air in the balloon more dense with respect to the surrounding atmosphere, causing the balloon to descend. More rapid increases in altitude can be achieved by lessening the weight of the balloon usually by dropping ballast, however this is limited by the amount of ballast available.
 +
 
 +
<!--T:83-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 11a -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=11b}} <!--T:31-->
 +
<noinclude><translate><!--T:84-->
 +
</noinclude>
 +
Adding more of the lighter than air gas to ascend, and spilling some of the gas in order to descend varies the altitude of a helium or hydrogen filled balloon.
 +
 
 +
<!--T:85-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 11b -->
 +
{{CloseReq}} <!-- 11 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=12}}
 +
<noinclude><translate><!--T:86-->
 +
</noinclude>
 +
<!-- 12. Describe how a pilot controls the lateral or horizontal movement of a flying balloon. -->
 +
Horizontal movement of a gas filled flying balloon is entirely at the mercy of air currents. The pilot can only vary the altitude so as to get into the path of air currents, such as the jet stream. This involves careful study of charts of air currents, close attention to weather data, and a certain element of trial and error. Older airships, like the Hindenburg, had a rudder and propellers to move it so that it did not have to depend on air currents.
 +
 
 +
<!--T:87-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 12 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=13}}
 +
<noinclude><translate></noinclude>
 +
<!-- 13. Build to completion one model hot air balloon ( or two if working in pairs ). -->
 +
===Materials=== <!--T:88-->
 +
* Tissue paper
 +
* Scissors
 +
* Glue Stick(s)
 +
* Sewing pins (optional)
 +
* Thin wire (22 gauge is suggested)
 +
* Needle-nose pliers & wire cutters
 +
* 1 50"x20" piece of Linoleum (for making balloon panel form)
 +
* A spool of string
 +
 
 +
===Directions for balloon panel form=== <!--T:34-->
 +
[[image:AYHAB-Model-Hot-Air-Balloons-draw2.png|thumb|400px|Illustration of distance from center]]
 +
 
 +
<!--T:35-->
 +
Use a rigid or semi-rigid material such as poster board or a piece of linoleum flooring. I would suggest a piece of linoleum flooring,as it is more rigid and can be used more times. Cut out a piece that is 50 inches long and 20 inches wide. For every other measurement, you will have to measure from the center of the form you are creating. You will need to mark each measurement on the outside edge (furthest from the center of the form).
 +
 
 +
<!--T:36-->
 +
* The first measurement is the very bottom of the form (and all others will be going from bottom to top) and is 3 1/2 inches each direction from the center.<br>
 +
* Seven inches from the bottom is another measurement of 3 1/2 inches from center.<br>
 +
* Four inches up the center line is a measurement of 4 7/8 inches from center.<br>
 +
* Four more inches up the center line is a measurement of 6 3/4 inches from center.<br>
 +
* Six inches up the center line is a measurement of 8 5/8 inches from center.<br>
 +
* Six more inches up the center line is a measurement of 9 5/8 inches from center (this is the widest measurement).<br>
 +
* Six inches beyond the widest measurement is a smaller measurement of 9 1/8 inches from center.<br>
 +
* Three inches up the line is a measurement of 7 1/2 inches from center.<br>
 +
* Three inches further is a measurement of 6 1/2 inches from center.<br>
 +
* Three inches further is a measurement of 4 3/4 inches from center.<br>
 +
* Three inches further is a measurement of 3 inches from center.<br>
 +
* Finally, 2 3/4 to 3 inches further is your top measurement. The top measurement is 1 5/8 inches from center.
 +
 
 +
<!--T:37-->
 +
Take the pen you are using to mark the measurements with and draw a line, starting from the bottom measurement, all the way around the outside of the measurement. It will look like a light bulb.
 +
 
 +
<!--T:38-->
 +
Cut along the line that you just drew to remove the extra material around the "light bulb" shape. That should give you the form needed to create the proper shape for the panels of your balloon.
 +
 
 +
===Directions for making balloon=== <!--T:39-->
 +
# Take 2 pieces of tissue paper and glue them end to end (vertically). Continue doing this with each set of tissue paper until you have 6 panels (a panel is 2 pieces of tissue paper glued end to end (vertically). You should only glue about a thumb's width or one straight line with the glue stick.
 +
# Once you have 6 panels, lay them one on top of another, making sure that one end of the stack has an even edge at the bottom of the panels.
 +
# Take the Panel Form and lay it on top of your 6 panels. Line up the bottom of the form with the straight edge of the 6 panels.
 +
# Trace, with a marker, along the edge of the form (making sure not to move the form or the panels). The form will not reach the other end your your panel stack. This is alright. Just keep tracing beyond the form in a diagonal line until you reach the top of your panel stack. Then remove the form from the stack of panels.
 +
# Take scissors and cut on the outside of the lines made earlier with the marker when you traced the panel form. When you are done, you should have two sets of scrap, one on each side of your panels. DO NOT THROW THESE AWAY! You may need to patch some panels that develop holes as well as use some of it to create a top for your balloon.
 +
# Remove two panels from your pile and set the other four aside. Place the two panels one-on-top-of-the-other, and then pull the top panel about one inch to the side of the bottom panel. With scissors, cut flaps along the exposed, curvy edge of the bottom panel, making the cuts two or three inches apart, and about a half inch deep. Do this all the way along one side of the bottom of the two panels. The flaps make it much easier to attach panels together.
 +
# Take a glue stick and apply glue to the top panels, right next to the tabs you just cut on the bottom panel. When applying the glue, you will only need one glue stick width of glue along the edge. Because the glue dries quickly, you may want to apply, at most, enough glue for 2 or 3 flaps at a time. Then you will fold over the flaps on the bottom panel onto the edge of the top panel where the glue was applied. Continue doing this until you have fully attached 2 of the panels together.
 +
# Take a third panel and lay it on top of the two panels that you just glued together. Lay it so that the edge of the top panel, of the 2 attached panels, that has not been glued is exposed about an inch.
 +
# Once again, cut flaps on the inch of exposed panel that are about a half inch deep. The glue and fold over the flaps to attach the third panel to the second panel. Now you should have 3 panels attached together. Continue repeating steps 8 & 9 until all of your panels have been attached. '''Remember to alternate which side you are cutting the flaps on so that you do not tamper with any of the joints of the other panels.'''
 +
# Once you have attached all 6 of your panels together, flip them over. Raise the top panel and fold the inner panels back. Do not crease the inner panels. Then replace the top panel.
 +
# Cut the bottom panel just as you have every panel before. Remember to make the cuts only about 1/2 inch deep. Then pull the top panel towards the edge of the bottom panel until you have the same width of the bottom panel as you would have for previous panels.
 +
# Apply glue to the top panel just as you have for every panel before. Remember that it may be easier to apply glue for only 2 or 3 panels at a time and then fold the flaps over before continuing to apply the glue.
 +
# Now. Open up your balloon. You will notice that it does not have a top yet. From the scraps that you saved, when you cut out your panels, pick as large a piece as possible. From this piece, cut as large a circle as you can. (You may fold the piece of paper over once or twice to make cutting out the circle easier.)
 +
# Apply glue to the circle you just cut out (around the outside edges by one or two glue stick widths). Then attach the circle to the top of your balloon to cover the hole.
 +
# Take some wire and cut roughly a 2 foot section off of the spool.
 +
# Take some needle-nose pliers and shape the wire into a rigid circle. (I suggest making a little loop in one end. Turning it slightly. Threading other end of the wire through the loop a little ways and the twisting the threaded wire around the looped end. This keeps the wire circle from expanding or contracting in size.)
 +
# Put the open end of the balloon through the wire circle. Then fold the balloon over the wire and glue the folded over end back to the balloon. (You may cut flaps in the open end of the balloon to make it easier to glue.) There will be more balloon surface than wire. You may have to fold the end of a panel or two over a little to decrease the amount of panel that you have to deal with while gluing the balloon over the wire.
 +
# At this point your balloon is finished. You will want to go over the entire surface of the balloon to make sure there are no holes in the panels, no unglued panel joints, no unglued balloon cap spots, or rips at the bottom where the wire is. If there are any of these issues, take some of your left over scraps (Aren't you glad you saved them?) and patch the balloon by gluing pieces from your scraps over any holes.
 +
 
 +
<!--T:89-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 13 -->
 +
{{ansreq|page={{#titleparts:{{PAGENAME}}|2|1}}|num=14}}
 +
<noinclude><translate><!--T:90-->
 +
</noinclude>
 +
<!-- 14. Successfully launch, fly, and recover the model hot air balloon(s) which you have built. -->
 +
 
 +
<!--T:41-->
 +
[[Image:launching balloon at night.jpg|thumb|300px|left|launching balloon at night]]
 +
 
 +
<!--T:42-->
 +
Take a single burner camp stove and use it to heat the air underneath your balloon. Be careful not to get the balloon too close to the flame as it will ignite and burn up.
 +
 
 +
<!--T:43-->
 +
A more efficient way of getting hot air into your balloon is to take some rigid dryer vent, cut notches that can be slid over the pot stabilizers on your camp stove, and then slide the vent pipe onto the stove. This causes the heated air to be channeled up the vent pipe into the balloon. However, this does not eliminate the possibility of your balloon igniting and burning up. You will have to keep the balloon from touching the vent pipe and also watch the balloon to make sure it doesn't start turning brown nearest the vent pipe.
 +
 
 +
<!--T:44-->
 +
You will need two (2) people to launch the balloon. One to hold the top end of the balloon up (until enough hot air is within the balloon), and the other to hold the balloon mouth over the stove. Before holding the balloon over the stove, tie a spool of string to the wire that keeps the form of the balloons mouth. Hold the balloon over the stove so that hot air may enter the balloon. Keep the balloon over the stove until it looks/feels as though it is ready to take off (usually anywhere from 30-45 seconds will do). When enough hot air has entered the balloon, release the balloon and let it fly up and away. Let the balloon fly for about twenty (20) seconds. When the balloon has successfully been flown pull on the string that you attached to the balloon to recover the balloon. The string keeps the balloon from being blown away as well as keeping it from flying into trees or other objects.
 +
 
 +
<!--T:45-->
 +
Please keep safe by using heat resistant gloves such as oven mitts or welders gloves. The metal duct does get hot. The balloon is not over the duct pipe long enough to catch fire. We had to have both gas burners going to get sufficient heat up the pipe. Happy flying. There is a good DVD called ''Night Crossing'' about a family who escaped over the Berlin border. They built two balloons and had two attempts to freedom.
 +
 
 +
<!--T:91-->
 +
<noinclude></translate></noinclude>
 +
{{CloseReq}} <!-- 14 -->
 +
<noinclude><translate></noinclude>
 +
==References== <!--T:46-->
 +
<noinclude></translate></noinclude>
 +
 
 +
[[Category:Adventist Youth Honors Answer Book/Do at home{{GetLangSuffix}}]]
 +
{{CloseHonorPage}}

Latest revision as of 02:14, 4 January 2023

Other languages:
English • ‎español
Hot Air Balloons

Skill Level

1

Year

2008

Version

25.11.2024

Approval authority

General Conference

Hot Air Ballooning AY Honor.png
Hot Air Balloons
Arts, Crafts and Hobbies
Skill Level
123
Approval authority
General Conference
Year of Introduction
2008
See also
Artisan Master Award


1

State the role each of the following played in the development of flying balloons.


1a

Joseph Michel Montgolfier and Jacques-Etienne Montgolfier


  • Joseph Michel Montgolfier

  • Jacques-Etienne Montgolfier

Joseph-Michel Montgolfier (26 August 1740 – 26 June 1810) and Jacques-Étienne Montgolfier (6 January 1745 – 2 August 1799) were the inventors of the montgolfière, or airship. The brothers succeeded in launching the first manned ascent, carrying a young physician and an audacious army officer into the sky.

Of the two brothers, it was Joseph who first contemplated building "machines". Joseph observed laundry drying over a fire incidentally form pockets that billowed upwards. Joseph set about building a box-like chamber 1 by 1 by 1.3 meters3 by 3 by 4 ft out of very thin wood and covering the sides and top with lightweight taffeta cloth. Under the bottom of the box he crumpled and lit some paper. The contraption quickly lifted off its stand and collided with the ceiling. Joseph then recruited his brother to balloon building.

The two brothers then set about building a contraption 3 times larger in scale (27 times larger in volume). The lifting force was so great that they lost control of their craft on its very first test flight on 14 December 1782. The device floated nearly 2 kilometres (about 1.2 mi). It was destroyed after landing by the "indiscretion" of passersby.


1b

Jean Francois Pilatre de Rozier and Francois Laurent Marquis d'Arlandes.


The first untethered balloon flight, by Rozier and the Marquis d'Arlandes on 21 November 1783.

Jean-François Pilâtre de Rozier (30 March 1754 – 15 June 1785) was a French chemistry and physics teacher, and one of the first pioneers of aviation. His balloon crashed near Wimereux in the Pas-de-Calais during an attempt to fly across the English Channel, and he and his companion, Pierre Romain, became the first known victims of an air crash.

In June 1783, he witnessed the first balloon flight of the Montgolfier brothers. On 19 September, he assisted with the untethered flight of a sheep, a cockerel and a duck from the front courtyard of the Palace of Versailles. After a variety of tests in October, he made the first manned free flight in history on 21 November 1783, accompanied by the ambitious Marquis d'Arlandes. During the 25-minute flight using a Montgolfier hot air balloon, they traveled 12 kilometres from the Château de la Muette to the Butte-aux-Cailles, then in the outskirts of Paris, attaining an altitude of 3,000 feet.


1c

Jacques Alexandre Cesar Charles and Nicolas Louis Robert.


In December of 1783, these two flew the first gas balloon, filled with hydrogen. This flight lasted for at least 2 hours, starting from the Tuileries gardens in Paris, and landing outside Paris where it was destroyed by terrified peasants.

Charles went on to discover Charles' Law which describes the relationship between the density of a gas and its temperature.


1d

Ben L. Abruzzo, Maxie L. Anderson, and Larry Newman


From 11 August to 17 August, 1978, these three completed the first transatlantic balloon flight in the Double Eagle II. They began their flight from Presque Isle, Maine and ended their flight at Miserey, France.

Ben Abruzzo and Larry Newman were also pilots on the Double Eagle V which in 1981 was the first balloon to cross the Pacific Ocean.


1e

Bertrand Piccard and Brian Jones


On March 1, 1999, Bertrand Piccard and Brian Jones began the first balloon flight to circumnavigate the earth. Their flight was a success and ended on March 20, 1999. The flight took 19 days and 21 hours. The flight started in Switzerland and ended in Egypt.



2

Cite the principle of Archimedes, and briefly describe how it applies to each of the following:


Archimedes' Principle states: any body fully or partially submerged in a fluid is buoyed up by a force equal to the weight of the fluid displaced.

2a

A piece of cork floating in a bowl of water


Cork is less dense than water, and weighs less than the volume of water displaced, causing the cork to float.


2b

A ship floating in the ocean


Ships, though made of dense materials, are shaped so that much of the interior is air. Because the weight of the ship and its cargo is less than the volume of water displaced, the ship will float.


2c

A hot air balloon floating in the atmosphere


As long as a balloon plus the gas it contains weighs less than the atmospheric air which it displaces, the balloon will float in the air.



3

Using a textbook of Chemistry, or a reference book of scientific tables, draw up a simple table showing the composition of air by weight and by volume.


Gas Air Percentage Weight of pure gas
Nitrogen 78% 1.25 g/liter
Oxygen 21% 1.43 g/liter
Argon .93% 1.78 g/liter
Carbon Dioxide .03% 1.96 g/liter
Other (including Neon, Helium,
Hydrogen, Xenon, & Radon)		 .04%

The average weight of air in a balloon can be worked out using rough percentages 80% Nitrogen and 20% oxygen as the make up of air. Atomic weight of Nitrogen is 14. Atomic weight of Oxygen is 16. Nitrogen and Oxygen gases are formed using two atoms. So for a balloon containing one mole (22.4 liters) of air, we can compute its weight:

80% x 28 + 30% x 32 = 0.8 x 28 + 0.2 x 32 = 22.4 + 6.4 = 28.8

So a balloon with 22.4 liters of air weighs 28.8 grams plus the weight of the balloon.



4

Draw up a simple table showing a comparison of the atomic number, atomic weight, and density of hydrogen, helium, nitrogen, and oxygen.



Atomic Number Atomic Weight Density (g/cm³)
Hydrogen 1 1.008 0.00008988
Helium 2 4.003 0.0001785
Nitrogen 7 14.01 0.0012506
Oxygen 8 16.00 0.001429


5

Name two gases that are used in flying gas filled balloons.


Hydrogen & Helium are both less dense than air and may be used when flying a balloon. Warm air is also used for flying balloons, since it is less dense than cold air.

  • Note: Hydrogen burns violently when ignited. After the destruction of the Hindenburg, hydrogen was largely abandoned for the flying of manned balloons.


6

Explain how heat/temperature affect the density of air, and how this applies to flying hot air balloons.


As described by Charles' Law, heat applied to a gas will cause its molecules to move farther apart, reducing it's density. When the air in a balloon is heated above the temperature of the surrounding air, the air in the balloon becomes less dense than the air outside the balloon. Because the balloon is less dense, it will float or rise. The greater the difference in temperature between the air in the balloon and the surrounding air, the greater the difference in density between the air inside and outside the balloon, which increases the lift that the balloon will generate. This explains why balloons are mostly launched in cooler weather.


7

Explain the role of each of the following in the structure and flying of a hot air balloon:


a. Envelope
The outer skin of the balloon, forming the container that holds the gas.
b. Support structure
The framework of larger balloons.
c. Throat
The lower opening through which the hot flame is applied to heat the air.
d. Fuel source
The fuel used to heat the air to make the balloon less dense than the surrounding air.


8

Name two materials that may be used for the envelope of a hot air balloon, and compare the advantages each accords because of its properties.


Paper
Paper may be used for model hot air balloons because of ease of acquisition and low price.
Plastic
Plastic may be used for model hot air balloons because it is water resistant, easy to work with, and easy to acquire.
Fabric
Fabric is usually used for larger, manned balloons. The fabric is specially treated.


9

Describe how flying balloons have served a useful function in


9a

Military campaigns


Military uses include: “eyes in the sky”, observation of enemy troops and positions, delivery of explosives to enemy positions, and defensive use of entangling incoming enemy flying craft.


9b

Scientific research


Scientific uses include instrument transport for data collecting, atmospheric studies, and aerial photography.



10

At what time of the day do most sport balloon flights take place? Why?


Early morning is best because the air has cooled over night making the difference of temperature inside & outside greater, thus increasing buoyancy.


11

Describe how a pilot controls the vertical movement of


11a

A hot air balloon


The pilot controls the vertical movement of a hot air balloon by burning more fuel to make the air in the balloon hotter, causes the air in the balloon to become less dense, making it rise. Conversely, turning off the flame and allowing the air in the balloon to cool renders the air in the balloon more dense with respect to the surrounding atmosphere, causing the balloon to descend. More rapid increases in altitude can be achieved by lessening the weight of the balloon usually by dropping ballast, however this is limited by the amount of ballast available.


11b

A gas filled balloon


Adding more of the lighter than air gas to ascend, and spilling some of the gas in order to descend varies the altitude of a helium or hydrogen filled balloon.



12

Describe how a pilot controls the lateral or horizontal movement of a flying balloon.


Horizontal movement of a gas filled flying balloon is entirely at the mercy of air currents. The pilot can only vary the altitude so as to get into the path of air currents, such as the jet stream. This involves careful study of charts of air currents, close attention to weather data, and a certain element of trial and error. Older airships, like the Hindenburg, had a rudder and propellers to move it so that it did not have to depend on air currents.


13

Build to completion one model hot air balloon (or two if working in pairs).


Materials

  • Tissue paper
  • Scissors
  • Glue Stick(s)
  • Sewing pins (optional)
  • Thin wire (22 gauge is suggested)
  • Needle-nose pliers & wire cutters
  • 1 50"x20" piece of Linoleum (for making balloon panel form)
  • A spool of string

Directions for balloon panel form

Illustration of distance from center

Use a rigid or semi-rigid material such as poster board or a piece of linoleum flooring. I would suggest a piece of linoleum flooring,as it is more rigid and can be used more times. Cut out a piece that is 50 inches long and 20 inches wide. For every other measurement, you will have to measure from the center of the form you are creating. You will need to mark each measurement on the outside edge (furthest from the center of the form).

  • The first measurement is the very bottom of the form (and all others will be going from bottom to top) and is 3 1/2 inches each direction from the center.
  • Seven inches from the bottom is another measurement of 3 1/2 inches from center.
  • Four inches up the center line is a measurement of 4 7/8 inches from center.
  • Four more inches up the center line is a measurement of 6 3/4 inches from center.
  • Six inches up the center line is a measurement of 8 5/8 inches from center.
  • Six more inches up the center line is a measurement of 9 5/8 inches from center (this is the widest measurement).
  • Six inches beyond the widest measurement is a smaller measurement of 9 1/8 inches from center.
  • Three inches up the line is a measurement of 7 1/2 inches from center.
  • Three inches further is a measurement of 6 1/2 inches from center.
  • Three inches further is a measurement of 4 3/4 inches from center.
  • Three inches further is a measurement of 3 inches from center.
  • Finally, 2 3/4 to 3 inches further is your top measurement. The top measurement is 1 5/8 inches from center.

Take the pen you are using to mark the measurements with and draw a line, starting from the bottom measurement, all the way around the outside of the measurement. It will look like a light bulb.

Cut along the line that you just drew to remove the extra material around the "light bulb" shape. That should give you the form needed to create the proper shape for the panels of your balloon.

Directions for making balloon

  1. Take 2 pieces of tissue paper and glue them end to end (vertically). Continue doing this with each set of tissue paper until you have 6 panels (a panel is 2 pieces of tissue paper glued end to end (vertically). You should only glue about a thumb's width or one straight line with the glue stick.
  2. Once you have 6 panels, lay them one on top of another, making sure that one end of the stack has an even edge at the bottom of the panels.
  3. Take the Panel Form and lay it on top of your 6 panels. Line up the bottom of the form with the straight edge of the 6 panels.
  4. Trace, with a marker, along the edge of the form (making sure not to move the form or the panels). The form will not reach the other end your your panel stack. This is alright. Just keep tracing beyond the form in a diagonal line until you reach the top of your panel stack. Then remove the form from the stack of panels.
  5. Take scissors and cut on the outside of the lines made earlier with the marker when you traced the panel form. When you are done, you should have two sets of scrap, one on each side of your panels. DO NOT THROW THESE AWAY! You may need to patch some panels that develop holes as well as use some of it to create a top for your balloon.
  6. Remove two panels from your pile and set the other four aside. Place the two panels one-on-top-of-the-other, and then pull the top panel about one inch to the side of the bottom panel. With scissors, cut flaps along the exposed, curvy edge of the bottom panel, making the cuts two or three inches apart, and about a half inch deep. Do this all the way along one side of the bottom of the two panels. The flaps make it much easier to attach panels together.
  7. Take a glue stick and apply glue to the top panels, right next to the tabs you just cut on the bottom panel. When applying the glue, you will only need one glue stick width of glue along the edge. Because the glue dries quickly, you may want to apply, at most, enough glue for 2 or 3 flaps at a time. Then you will fold over the flaps on the bottom panel onto the edge of the top panel where the glue was applied. Continue doing this until you have fully attached 2 of the panels together.
  8. Take a third panel and lay it on top of the two panels that you just glued together. Lay it so that the edge of the top panel, of the 2 attached panels, that has not been glued is exposed about an inch.
  9. Once again, cut flaps on the inch of exposed panel that are about a half inch deep. The glue and fold over the flaps to attach the third panel to the second panel. Now you should have 3 panels attached together. Continue repeating steps 8 & 9 until all of your panels have been attached. Remember to alternate which side you are cutting the flaps on so that you do not tamper with any of the joints of the other panels.
  10. Once you have attached all 6 of your panels together, flip them over. Raise the top panel and fold the inner panels back. Do not crease the inner panels. Then replace the top panel.
  11. Cut the bottom panel just as you have every panel before. Remember to make the cuts only about 1/2 inch deep. Then pull the top panel towards the edge of the bottom panel until you have the same width of the bottom panel as you would have for previous panels.
  12. Apply glue to the top panel just as you have for every panel before. Remember that it may be easier to apply glue for only 2 or 3 panels at a time and then fold the flaps over before continuing to apply the glue.
  13. Now. Open up your balloon. You will notice that it does not have a top yet. From the scraps that you saved, when you cut out your panels, pick as large a piece as possible. From this piece, cut as large a circle as you can. (You may fold the piece of paper over once or twice to make cutting out the circle easier.)
  14. Apply glue to the circle you just cut out (around the outside edges by one or two glue stick widths). Then attach the circle to the top of your balloon to cover the hole.
  15. Take some wire and cut roughly a 2 foot section off of the spool.
  16. Take some needle-nose pliers and shape the wire into a rigid circle. (I suggest making a little loop in one end. Turning it slightly. Threading other end of the wire through the loop a little ways and the twisting the threaded wire around the looped end. This keeps the wire circle from expanding or contracting in size.)
  17. Put the open end of the balloon through the wire circle. Then fold the balloon over the wire and glue the folded over end back to the balloon. (You may cut flaps in the open end of the balloon to make it easier to glue.) There will be more balloon surface than wire. You may have to fold the end of a panel or two over a little to decrease the amount of panel that you have to deal with while gluing the balloon over the wire.
  18. At this point your balloon is finished. You will want to go over the entire surface of the balloon to make sure there are no holes in the panels, no unglued panel joints, no unglued balloon cap spots, or rips at the bottom where the wire is. If there are any of these issues, take some of your left over scraps (Aren't you glad you saved them?) and patch the balloon by gluing pieces from your scraps over any holes.


14

Successfully launch, fly, and recover the model hot air balloon(s) which you have built.


launching balloon at night

Take a single burner camp stove and use it to heat the air underneath your balloon. Be careful not to get the balloon too close to the flame as it will ignite and burn up.

A more efficient way of getting hot air into your balloon is to take some rigid dryer vent, cut notches that can be slid over the pot stabilizers on your camp stove, and then slide the vent pipe onto the stove. This causes the heated air to be channeled up the vent pipe into the balloon. However, this does not eliminate the possibility of your balloon igniting and burning up. You will have to keep the balloon from touching the vent pipe and also watch the balloon to make sure it doesn't start turning brown nearest the vent pipe.

You will need two (2) people to launch the balloon. One to hold the top end of the balloon up (until enough hot air is within the balloon), and the other to hold the balloon mouth over the stove. Before holding the balloon over the stove, tie a spool of string to the wire that keeps the form of the balloons mouth. Hold the balloon over the stove so that hot air may enter the balloon. Keep the balloon over the stove until it looks/feels as though it is ready to take off (usually anywhere from 30-45 seconds will do). When enough hot air has entered the balloon, release the balloon and let it fly up and away. Let the balloon fly for about twenty (20) seconds. When the balloon has successfully been flown pull on the string that you attached to the balloon to recover the balloon. The string keeps the balloon from being blown away as well as keeping it from flying into trees or other objects.

Please keep safe by using heat resistant gloves such as oven mitts or welders gloves. The metal duct does get hot. The balloon is not over the duct pipe long enough to catch fire. We had to have both gas burners going to get sufficient heat up the pipe. Happy flying. There is a good DVD called Night Crossing about a family who escaped over the Berlin border. They built two balloons and had two attempts to freedom.



References

Retrieved from "https://wiki.pathfindersonline.org/index.php?title=AY_Honors/Hot_Air_Balloons/Answer_Key&oldid=591563"