Difference between revisions of "AY Honors/Carpentry/Requirements/es"
(Created page with "</noinclude>Sierra radial fija <noinclude>") |
(Created page with "</noinclude>Sierra ingletadora (miter) <noinclude>") |
||
Line 14: | Line 14: | ||
<noinclude></noinclude><section end=req1c /></b> | <noinclude></noinclude><section end=req1c /></b> | ||
− | :<b>d. <section begin=req1d /><noinclude> | + | :<b>d. <section begin=req1d /><noinclude></noinclude>Fresadora/caladora |
− | </noinclude> | + | <noinclude></noinclude><section end=req1d /></b> |
− | <noinclude | ||
− | |||
− | :<b>e. <section begin=req1e /><noinclude> | + | :<b>e. <section begin=req1e /><noinclude></noinclude>Sierra de calar/de vaivén |
− | </noinclude> | + | <noinclude></noinclude><section end=req1e /></b> |
− | <noinclude | ||
− | |||
− | :<b>f. <section begin=req1f /><noinclude> | + | :<b>f. <section begin=req1f /><noinclude></noinclude>Moldeador |
− | </noinclude> | + | <noinclude></noinclude><section end=req1f /></b> |
− | <noinclude | ||
− | |||
− | :<b>g. <section begin=req1g /><noinclude> | + | :<b>g. <section begin=req1g /><noinclude></noinclude>Sierra ingletadora (miter) |
− | </noinclude> | + | <noinclude></noinclude><section end=req1g /></b> |
− | <noinclude | ||
− | |||
− | <b>2. <section begin=req2 /><noinclude> | + | <b>2. <section begin=req2 /><noinclude></noinclude>Demostrar cómo utilizar las siguientes herramientas: |
− | </noinclude> | + | <noinclude></noinclude><section end=req2 /></b> |
− | <noinclude | ||
− | |||
:<b>a. <section begin=req2a /><noinclude><div lang="en" dir="ltr" class="mw-content-ltr"> | :<b>a. <section begin=req2a /><noinclude><div lang="en" dir="ltr" class="mw-content-ltr"> | ||
Line 166: | Line 156: | ||
<section end=challenge /> | <section end=challenge /> | ||
− | <b>{{Localize|Note}}: <section begin=reqNote /><noinclude> | + | <b>{{Localize|Note}}: <section begin=reqNote /><noinclude></noinclude> |
− | </noinclude> | + | <noinclude></noinclude><section end=reqNote /></b> |
− | <noinclude | ||
− | |||
<section end=Body /> | <section end=Body /> | ||
− | <noinclude> | + | <noinclude>[[Category:Honor Requirements/es|{{#titleparts:{{PAGENAME}}|1|2}}]] |
− | [[Category:Honor Requirements|{{#titleparts:{{PAGENAME}}|1|2}}]] | + | [[Category:Honor Requirements Revision 3/es|{{#titleparts:{{PAGENAME}}|1|2}}]] |
− | [[Category:Honor Requirements Revision 3|{{#titleparts:{{PAGENAME}}|1|2}}]] | + | <noinclude></noinclude> |
− | <noinclude | ||
− |
Revision as of 16:37, 4 May 2021
1. Describir la función de las siguientes herramientas:
- a. Sierra de cinta
- b. Sierra radial fija
- c. Lijadora de banda
- d. Fresadora/caladora
- e. Sierra de calar/de vaivén
- f. Moldeador
- g. Sierra ingletadora (miter)
2. Demostrar cómo utilizar las siguientes herramientas:
- a.
Block Plane
- b.
Circular Saw (cut a straight line)
- c.
Framing Square
- d.
Hammer
- e.
Hand Saw (cut a straight line)
- f.
Level
- g.
Measuring Tape
- h.
Nail Set
- i.
Plumb Bob
- j.
Wood Chisel
3.
Describe the use of and distinguish between the following types of nails: 20 Penny, 16 Penny, 12 Penny, 8 Penny, 6 Penny, Finish, Brad, Roofing, Screw Nail, Sinker, Common, and Galvenized
4.
Assist in erecting a building not less than 6x8 feet in ground dimensions with a gable roof and at least one door and one window, demonstrating ability to measure and use tools from requirement 2.
5.
When building the above project, use all of these features:
- a.
Floor Joist
- b.
Sub Floor
- c.
Shoe Plate
- d.
Top Plate
- e.
Double Plate
- f.
Conventional Roof or Trusses
- g.
Felt Roof
- h.
Shingles
- i.
Window with Weight-bearing Header
- j.
Door with Weight-bearing Header
- k.
Fascia on Eaves
- l.
Siding
Nota: